how to bypass a lid switch on a whirlpool washer

How to Bypass Lid Switch on Whirlpool Washer: Easy Steps

By Emily Martin
AD

Are you dealing with a Whirlpool washer that's not spinning due to a faulty lid switch? Don't let this common issue leave you with a pile of wet clothes. With a little patience and the right steps, you can bypass the lid switch and get your washer spinning again. Here's a comprehensive, step-by-step guide to help you navigate this process safely and effectively.

Before we dive into the steps, remember that working with electrical components can be dangerous. Always unplug your washer and turn off the power at the circuit breaker before starting. Also, working on your washer may void its warranty, so proceed at your own risk.

Understanding the Lid Switch

The lid switch on your Whirlpool washer is a safety feature that prevents the machine from operating when the lid is open. When you close the lid, the switch completes an electrical circuit, allowing the washer to run. If the switch is faulty, it may not close properly, preventing the washer from spinning.

AD
Whirlpool Washing Machine Not Starting - The Lid Or Door Switch
Whirlpool Washing Machine Not Starting - The Lid Or Door Switch
the words bypass new washer lid lock are displayed in black and white letters on a white background
the words bypass new washer lid lock are displayed in black and white letters on a white background
the maytag washer lid lock bypass guide and tips machine answered
the maytag washer lid lock bypass guide and tips machine answered

In many cases, the issue is not the switch itself, but theDoor Lock Assembly (DLA), which can get stuck or jammed. We'll guide you through checking and bypassing both the switch and the DLA.

possibles Symptoms and Causes

Before you start, let's ensure you're dealing with a lid switch or DLA issue. If your washer's control panel shows an error code like 'FF' or 'FE', or it won't spin even when the lid is closed, it's likely a lid switch or DLA problem. The lid switch or DLA can become faulty due to wear and tear, repeated usage, or even a slight impact.

Washing machine will not spin, door switch replacement - Household Repairs
Washing machine will not spin, door switch replacement - Household Repairs
Amana / Maytag Washer Not Spinning - How to Test, Replace and Bypass the Lid Switch
Amana / Maytag Washer Not Spinning - How to Test, Replace and Bypass the Lid Switch

Here's a quick check: Try running a cycle with the lid held shut by your hand. If the washer runs normally, it could be a lid switch issue. If the washer still won't spin, it might be a problem with the DLA.

Gathering Tools and Replacement Parts

Before you start, gather the necessary tools and replacement parts. You'll need a Phillips #1 or #2 screwdriver, aflathead screwdriver, needle-nose pliers, and a multimeter (for checking continuity). You may also need a replacement lid switch or DLA, which usually costs around $20 to $40. Be sure to get the correct part for your washer model.

AD

It's a good idea to have a washing machine repair manual for reference. You can find them at local bookstores, online, or even as an eBook. Make sure to get one specific to your washer model for the most accurate information.

Bypassing the Lid Switch

Now that you've prepared everything, let's proceed with bypassing the lid switch. We'll first check if the switch is faulty, then show you how to bypass it if needed. Remember, always work safely and unplug your washer before starting.

Checking the Lid Switch

First, locate the lid switch near the top of the washer. It's usually a small rectangular component with a wire harness connected to it. Carefully unplug the wire harness and use your multimeter to test the switch. Set your multimeter to ' Continuity Test' mode (usually symbolized by a wave) and touch the probes to the terminals on the switch.

AD

If the switch is good, you should hear a beep or see the needle on the multimeter move. If not, the switch is likely faulty and needs to be replaced. Skip to the ' Replacing the Lid Switch' section. If the switch is good, proceed to checking the DLA.

Checking and Clearing the Door Lock Assembly (DLA)

The DLA can sometimes cause issues similar to a faulty lid switch. To check the DLA, open the washer's control panel and locate the small screw or cover that gives you access to the DLA. This is usually at the top of the washer, near the lid. Remove the screw or cover and carefully disconnect the electrical harness.

With the harness disconnected, try moving the DLA. It should move freely. If it's stuck or jammed, you may need to adjust or replace it. In some cases, simply bending the DLA arm back slightly can free it up. If you need to replace it, follow the same procedure as replacing the lid switch, but with the DLA part.

AD

Bypassing the Lid Switch

If you've checked both the lid switch and DLA, and neither seems to be the issue, you can try bypassing the lid switch. This involves creating a direct path for electricity around the switch using a jumper wire. Here's how:

Locate the wire harness connected to the lid switch. Inside the harness, you should see two or three wires. Two of them are connected to the terminals on the switch. The third wire (if present) is usually just a grounding wire and can be ignored. Carefully strip some of the insulation off the ends of the wires using your needle-nose pliers.

Now, use a piece of wire (a paperclip works too) to connect one of the switch terminals directly to the other wire in the harness. This creates a direct pathway for electricity, bypassing the switch. Once you've made the connection, your washer should spin normally again.

Replacing the Lid Switch

If bypassing the lid switch doesn't work, or you prefer a more permanent solution, you'll need to replace the switch. Here's how:

First, unplug your washer and turn off the power at the circuit breaker. Then, remove the screws securing the back panel of the washer. With the panel removed, you should be able to see the lid switch. Disconnect the wire harness.

Take your new lid switch and carefully attach the wire harness to it, making sure to connect it exactly as the old switch was connected. Secure the new switch in place, replace the back panel, and restore power to the washer. Your washer should now spin normally.

Congratulations, you've successfully bypassed or replaced the lid switch on your Whirlpool washer! While this process can seem daunting, with patience and careful attention to detail, it's definitely doable. Remember, always work safely and if you're unsure about any step, consult a professional. Happy washing!

AD