how to wire for recessed lighting

How to Wire for Recessed Lighting

By Laura Hernandez
AD

Are you planning to add a touch of sophistication to your living space or workspace? Doing so with the right lighting can be not only inviting but also cost-effective with recessed lighting. Recessed lighting, also known as can lights, are not only unobtrusive and sleek, but also highly energy-efficient. If you're wondering how to wire for recessed lighting, you've come to the right place. Let's dive into this comprehensive guide that will take you through every step of the process.

Gathering Your Tools and Materials

Before you embark on this exciting project, you'll need to gather all the necessary tools and materials. Having everything ready to go will ensure that your project runs as efficiently as possible.

Here's a list of what you'll need:

  • A can (recessed) light
  • NM cable (14/3or 12/3)
  • Wire stripper
  • Screwdriver
  • Fish tape
  • Drill
  • Recessed light housing

Choosing the Right Recessed Light Housing

First, you need to choose the right housing for your light. This will depend on the depth of your ceiling. The most common types are the new construction housing and the remodel housing.

New construction housing is used when there's no drywall in place. On the other hand, remodel housing is designed for existing ceilings, providing less depth and allowing it to fit into the ceiling cavity of an existing home.

Determining the Right Lighting Layout

Next, you need to plan where you want your lights. A good rule of thumb is to have at least one light for every 400 square feet of space. However, this can vary depending on your specific requirements.

Also, consider factors such as room size, the intended use of the space, and any potential obstacles like plumbing or ducts. Sketching out a simple diagram can also help you visualize the layout and make adjustments as needed.

Installing Recessed Lighting: Step-by-Step

Now that you've gathered your materials and planned your layout, it's time to start the installation process.

Remember, safety first! Always turn off the electricity to the area you'll be working in at your electrical panel. It's also a good idea to wear safety glasses to protect your eyes from any debris.

Running the Wiring

Begin by running your NM cable from your electrical panel to the location where you want your first light to be. This cable will also act as a power source for any additional lights you plan to install.

If you're using a 14/3 cable, the black and white wires are your power supply, and the red and green are for switches. For a 12/3 cable, the blue and yellow wires replace the red in the 14/3 cable, and they are for switches or dimmers.

Installing the Recessed Light Housing

Once your wire is in place, it's time to install the housing for your light. Use your drill to make a hole in your ceiling that matches the size of your housing. Remember to wear safety glasses to protect your eyes from any debris.

After the hole is made, insert the housing and secure it with the provided screws. Then, route your NM cable through the housing and into the attic space above.

Wiring Your Light

Next, you'll need to strip the sheathing from your NM cable to expose the individual wires. Connect the black and white wires to the appropriate terminals in your can light. Then, use the switch leg (red or blue) to connect to your switch.

Don't forget to secure your light with the spring clip provided. This will hold your light in place as you screw in the trim.

Adding Additional Lights

If you're installing multiple lights, use the "home run" method, meaning that you run a single cable from your electrical panel to your first light, and then from that light to the remaining lights in the row.

For each additional light, install the housing as described above, then connect the new light to the previous one using a "pigtail." This is just a short piece of cable that connects the last light to the new one. Repeat this process until all your lights are installed.

Safety Checks and Testing

Once all your lights are installed, it's time to do a final safety check. Ensure that all wires are securely tightened and that there are no loose connections.

Then, turn the power back on at your electrical panel and test your lights. If they turn on and off as expected, you're in good shape! Remember, if anything seems amiss, don't hesitate to call a professional electrician.

Installing the Trim

Finally, it's time to install the trim. This is the part of the light that sits flush with your ceiling. It not only completes the look of your can light, but it also helps to focus the light.

Simply insert the trim into the opening in your ceiling and secure it with the provided screws. Make sure to leave enough room for the light bulb.

There you have it! You've now successfully wired for recessed lighting. Remember, it's essential to keep safety in mind throughout the entire process. If at any point you feel unsure, don't hesitate to consult with a professional. Now, enjoy your new, stylish, and energy-efficient lighting!

How to Install Recessed Lighting | FixThisBuildThat
How to Install Recessed Lighting | FixThisBuildThat
How to Wire Recessed Lighting Diagram (Guide With Photos)
How to Wire Recessed Lighting Diagram (Guide With Photos)
How to Wire Canless Recessed Lighting
How to Wire Canless Recessed Lighting
AD