how to wire dual voice coil subwoofer

How to Wire a Dual Voice Coil Subwoofer

By Thomas Davis
AD

If you're looking to beef up your audio system, you might be considering the installation of a dual voice coil subwoofer. These powerful units can significantly enhance your sound experience. However, wiring a dual voice coil subwoofer can be a bit tricky if you're not sure what you're doing. Don't worry though, we're here to guide you through the process with our comprehensive, step-by-step guide. Let's dive in!

Before we start, it's crucial to understand that the wiring process for a dual voice coil subwoofer involves connecting both coils in parallel and then connecting them to your amplifier. This setup allows you to wire the subwoofer using a single channel on your amp. Now, let's get started.

Understanding Your Subwoofer

Before you start, it's vital to understand your subwoofer's specifications. Most notably, you'll want to know the impedance of each voice coil. Typical dual voice coil subs have either 2 ohms or 4 ohms per coil. Knowing this will help you determine the total impedance when both coils are connected in parallel and how much power your amplifier should handle.

AD
the different types of subwoofer wiring in this diagram are shown below and below
the different types of subwoofer wiring in this diagram are shown below and below
4 Ohm Dual Voice Coil Subwoofer Wiring Diagram
4 Ohm Dual Voice Coil Subwoofer Wiring Diagram
two different types of dual voice coils and one type of power source are shown in this diagram
two different types of dual voice coils and one type of power source are shown in this diagram

Once you've gathered your subwoofer's specifics, it's time to gather your tools and materials. You'll need your dual voice coil subwoofer, an amplifier, speaker wire, and wire strippers. The process will involve connecting the subwoofer's input terminals to your amplifier's speaker output. Let's break it down further.

Wiring the Subwoofer

First, locate the voice coil terminals on your subwoofer. These are usually marked with symbols or numbers (1, 2, 3, 4). Take your speaker wire and strip about an inch of insulation from each end. Twist the exposed copper wire to prevent fraying.

4 Ohm Dual Voice Coil Wiring Diagram
4 Ohm Dual Voice Coil Wiring Diagram
wiring diagram for 4 ohm dual voice coil subwoofer connection and installation
wiring diagram for 4 ohm dual voice coil subwoofer connection and installation

Now, take one wire and connect it to both terminal 1 and terminal 3. Do the same with the other wire, connecting it to both terminal 2 and terminal 4. These connections should be tight and secure to ensure a good electrical connection. Once you've done this, your subwoofer's voice coils are connected in parallel.

Connecting to the Amplifier

Next, you'll connect these wires to your amplifier. Locate the same terminals on your amp's speaker output. Usually, these are labeled with plus and minus signs (Positive and Negative). Take the wire connected to terminals 1 and 3 on your subwoofer and connect it to the positive terminal on your amp. Connect the other wire to the negative terminal.

AD

Make sure your connections are secure and tight. Remember, these wires carry electrical current, so a poor connection can lead to humming, buzzing, or even power issues. Once you've made these connections, your dual voice coil subwoofer is now wired and ready to go.

Testing and Fine-Tuning

Before you power up your system, double-check all your connections to ensure they're secure. Then, gently power on your amplifier. Start with a low volume and gradually increase it to test the subwoofer's sound quality. If everything sounds good, you're all set!

However, if you notice any issues like distortion or poor sound quality, you might need to fine-tune your setup. This could involve adjusting your amp's settings, like the crossover frequency or gain, or even swapping out your speaker wire for a higher quality option.

AD

Safety Tips

Always remember to handle electrical components with care. Never wire your system with the power on, and always follow proper safety procedures. If you're unsure about any part of the process, it's always best to consult a professional.

Finally, once you've successfully wired your dual voice coil subwoofer, take a moment to enjoy your enhanced audio experience. The deep, powerful bass notes you'll now hear are a testament to your newfound wiring skills. Happy listening!

AD