how to wire double switch

How to Wire a Double Switch: Step-by-Step Guide

By James Harris
AD

Wiring a double switch can empower your electrical circuits with control over two separate lights or outlets from a single wall switch. This handy setup allows you to manage two distinct areas with a single switch, such as controlling both a ceiling light and a table lamp. Let's dive into the step-by-step process of wiring a double switch like a pro.

The double switch, sometimes called a 3-way switch, comprises three terminals: the common, and two traveler terminals. Each traveler terminal connects to one of the two switches, and they both connect to the common terminal at the second switch. Understanding this configuration is key to wiring a double switch correctly.

Gathering Your Tools and Materials

Safety first! Before you start, ensure you have the right tools and materials:

AD
How to Wire Double Switch? 2-Gang, 1-Way Switch - IEC & NEC
How to Wire Double Switch? 2-Gang, 1-Way Switch - IEC & NEC
How to wire a double switch Combination two switches; double switch. DIY
How to wire a double switch Combination two switches; double switch. DIY
three way switch wiring with two lights and one light on the other side, in parallel to
three way switch wiring with two lights and one light on the other side, in parallel to
  1. Double switch
  2. 14/3 non-metallic (NM) sheathed cable ( Romex)
  3. 14/2 NM cable (for power)
  4. Wire stripper
  5. Wire connectors (wire nuts)
  6. Wire connectors clips (for wires going into switch boxes)
  7. Screwdrivers (flathead and Phillips)
  8. Electrical tape
  9. Wire stare grounded faceplate
  10. Voltage tester

Double-check that the power to the circuit is off by testing the wires with a voltage tester before you begin. Safety first! Always!

Now, let's discuss preparing your cables and boxes for installation.

How to Wire Combo Switch & Outlet? Combo Device Wiring
How to Wire Combo Switch & Outlet? Combo Device Wiring
How to wire a Double Switch
How to wire a Double Switch

Running the Wires

Run the 14/3 cable from the power source (such as your electrical panel) to the first switch box. Installing a junction box at the midpoint, if necessary, helps manage the cable length. Connect the 14/2 power cable to the junction box for the power feed.

From the first switch box, run the 14/3 cable to the second switch box, ensuring it's long enough to reach both switches. After that, run another 14/2 cable from the second switch box back to the electrical panel to disconnect the old wiring.

AD

Wiring the Second Switch Box

Now, let's wire the second switch box, which will be our load/light side:

  1. Strip ¾ inches of insulation from the 14/3 and 14/2 cables.
  2. Connect the black (hot) wire of the 14/2 power cable to the common terminal of the double switch.
  3. Connect the white wires (neutral) of both cables to each other using a wire nut, and then connect to the neutral bus in the electrical panel.
  4. Connect the green or bare copper wire (ground) from both cables to the ground bus in the electrical panel.
  5. Connect the ground terminal of the switch to the ground wire using a pigtail (add a short piece of green or bare wire to the switch's ground terminal, then connect to the ground bus).

Next, connect the traveler wires from the 14/3 cable to the two traveler terminals on the switch.

Wiring the First Switch Box

Now let's wire the first switch box, which will be the line/switch leg:

AD
  1. Strip ¾ inches of insulation from the 14/3 cable.
  2. Connect the black (hot) wire of the 14/3 cable to one of the traveler terminals on the double switch.
  3. Connect the other black wire from the 14/3 cable (the second black, or traveler wire) to the other traveler terminal.
  4. Connect the white (neutral) and green/bare (ground) wires to the neutral bus and ground bus, respectively, in the electrical panel.

At this point, the electrical work is done. The last step is to attach the switches to the mounting boxes and secure with screws, ensuring they're flush with the wall surface.

Installing the Faceplate

Once the switches are secure, install the grounded faceplate, ensuring the grounding screw is used to connect the ground terminal of the switch.

Congratulations! You've successfully wired a double switch. Now you can test your setup by flipping the switches and verifying each one controls the corresponding light or outlet.

AD

Always double-check your work, and if you're unsure about any aspect of the process, don't hesitate to consult a licensed electrician. Safety is paramount when working with electricity. Happy wiring!

AD