how to wire can lights in series

How to Wire Can Lights in Series: A Step-by-Step Guide

By John Hernandez
AD

So, you've decided to upgrade your home's lighting with can lights, but you're not sure how to wire them in series? You're in the right place. Wiring can lights in series involves connecting them one after the other to a single power source. This method is ideal when you want to control all the lights with a single switch. Let's dive in and explore the step-by-step process, from planning to the final connection.

Before we start, let's ensure you have all the necessary tools and components. You'll need a voltage tester, wire strippers, a fish tape (for fishing wires through walls), stranded 14/3 non-metallic (NM) sheathed cable, can lights with supply leads attached, and a multi-plug connector. Remember, safety first - always turn off the power at your circuit breaker before starting any electrical work.

Planning Your Can Light Layout

Start by sketching out your can light layout. Decide where each light will go, considering factors like room size, spacing, and the task you're illuminating. Generally, can lights should be spaced evenly, with no fixture more than 6 inches from the ceiling and no wider than 8 feet apart.

AD
How to Wire Canless Recessed Lighting
How to Wire Canless Recessed Lighting
How to Wire Recessed Lighting Diagram (Guide With Photos)
How to Wire Recessed Lighting Diagram (Guide With Photos)
three way switch wiring with two lights and one light on the other side, in an electrical
three way switch wiring with two lights and one light on the other side, in an electrical

Once you have your layout, measure and mark the ceiling where each light will go. Use a stud finder to locate ceiling joists and avoid drilling into them. This step ensures a secure mounting point for your can lights and prevents damaging any wiring or structural elements.

Fishing Wires Through Walls

Next, you'll need to run the 14/3 NM cable through the walls or ceiling to connect your can lights. Start by drilling a small hole at the first mark, enough to insert your fish tape. Feed the fish tape through the hole, unreeling as you go. Once it emerges from the other side, tape the NM cable to the fish tape and pull it back through.

Best way to wire multiple lights in multiple rooms on single circuit?
Best way to wire multiple lights in multiple rooms on single circuit?

Repeat this process for each can light location, ensuring you have enough cable to reach from one light to the next. Keep in mind that you'll need a continuous flow of power, so each light should be within reach of the previous one's supply wires.

Using a Multi-Plug Connector

A multi-plug connector, also known as aBig-Box, is a convenient way to connect your can lights in series. This device allows you to daisy-chain your lights, connecting each one to the next without needing to strip and twist individual wires.

AD

Before installing the connector, strip the insulation from the NM cable where it meets each can light. This will expose the three individual wires: hot (black), neutral (white), and ground (green or bare). Then, insert the connector into the can light's junction box, and secure it with screws.

Wiring the Multi-Plug Connector

Now it's time to wire the connector. First, connect the ground wire (green or bare) from the NM cable to the ground wire on the connector. Next, connect the neutral wires (white). Finally, connect the hot wires (black) in the following sequence:

  • From the power source, connect to the first can light's hot wire circulating through the connector.
  • Connect the last can light's hot wire to the power source.

This creates a loop, ensuring all lights are connected in series and will turn on and off together with a single switch.

AD

Installing the Can Lights

With the wiring in place, it's time to install the can lights themselves. Press each light's spring clip into the junction box, mount the light inside the hole you've prepared, and secure the can light in place with screws provided. Ensure the screw head remains below the outline of the can light to avoid scratching the ceiling.

Test your new can lights by flicking the switch. If everything is wired correctly, they should turn on and off in unison. If any lights require additional support or further adjustments, delve into the appropriate troubleshooting steps.

Congratulations! You've successfully wired your new can lights in series. With this new lighting scheme, you've not only enhanced your home's ambiance but also demonstrated your prowess in DIY electrical work. Next time you embark on a lighting project, you'll have the confidence and know-how to tackle it head-on. So, start planning your next upgrade with the same enthusiasm and dedication you showed with these can lights.

AD
AD