How to Wire a Dual Outlet: Step-by-Step Guide
Need to power two appliances or devices at the same location but short on outlets? Wiring a dual outlet might be just the solution you're looking for. It's a straightforward DIY project that can save you the hassle and expense of calling an electrician. But remember, safety first! Always turn off the power at the circuit breaker before starting any electrical work.
Before we dive into the steps, let's understand what you'll need: a dual outlet (receptacle), faceplate, wall patch, underwater staples, 14/3 or 12/3 non-metallic (NM) sheathed electrical cable, wire stripper, voltage tester, drill, and a screwdriver. Now, let's get started.
Preparation and Planning
Before you pick up your tools, ensure you've carefully planned your project. Measure your wall to determine the exact location of the new outlet. It's generally best to position it about 48 inches from the floor, or 4-6 inches below the bottom of a standard switch or outlet.
Once you've located the ideal spot, mark the exact point where you'll cut the hole. Use a scrap piece of drywall to test fit the faceplate and ensure the outlet will be centered in the wall.
Safety First: Turning Off the Power
This step is crucial. Locate your main service panel and turn off the power to the circuit you'll be working on. Use a voltage tester to confirm that the wire is dead before proceeding.
Label the wires in the existing outlet box using colored electrical tape so you can easily match them when it's time to wire the new outlet. Then, carefully remove the faceplate and the outlet, noting how the wires are connected, as you'll need to replicate this when wiring the new dual outlet.
Preparing the Wall
Using a drywall saw or a jab saw, cut out the hole in the wall where you'll install the new outlet. Make it slightly larger than the outlet box, but remember, you can always enlarge it if needed.
Fish the new electrical cable through the hole and up into the attic or wall cavity. Use an_trainer] to secure the cable in place as you go. Once the cable is fully run and secure, mark where the outlet box will be located on the other side of the wall.
Wiring the Dual Outlet
Now that the wall is prepared and the cable is run, it's time to wire the new dual outlet.
Strip the insulation off the Nm cable, exposing about 2.5 inches of the individual wires. Remember, the white wire is neutral, the black wire(s) is (are) hot, and the green or bare wire is ground.
Connecting the Ground Wires
First, connect the ground wires. Twist the ends of all ground wires together and capture them with a wire nut. This includes the ground wire from the existing outlet, the ground wire from the new cable, and the ground wire from the new dual outlet.
Strip the insulation from the end of the ground wire from the new outlet and connect it to the green screw on the outlet. Tighten gently to ensure a good connection.
Connecting the Neutral Wires
Next, connect the neutral wires. Twist them together and capture them with a wire nut, just as you did with the grounds. Strip about 1/2 inch of insulation from the neutral wire at the new outlet and connect it to the silver screw.
Remember that neutral and ground are not the same. Neutral wires are typically white, but they can also be gray or uncolored. Ground wires are always green or bare.
Connecting the Hot Wires
Now, connect the hot wires. Since this is a dual outlet, you'll need to connect two hot wires. Twist the hot wires from the existing outlet and the new cable together. Ensure you're using the correct size wire nut for the number of wires.
Strip about 1/2 inch of insulation from the hot wire(s) at the new outlet and connect it(them) to the brass-colored screw(s), making sure to tighten gently for a good connection.
Finishing Up
Once all the wires are connected, carefully insert the dual outlet into the outlet box. Screw it in place, ensuring it's secure and the cover plate can be properly installed.
Replace the faceplate and, if needed, repair any drywall damage. Then, turn the power back on at the main service panel. Test your new dual outlet using a voltage tester and a small appliance to ensure it's working properly.
Congratulations! You've just successfully wired a dual outlet. This skill can come in handy for many other home improvement projects. Always remember to prioritize safety and double-check your work.