how to winterize a sea doo

Winterize Your Sea-Doo: A Step-by-Step Guide

By Nicole Davis
AD

As the leaves turn and the temperatures drop, it's time to start thinking about storing your Sea-Doo away for the winter. Winterizing your personal watercraft (PWC) is crucial to prevent damage and ensure it's ready to hit the waves when spring arrives. This comprehensive guide will walk you through the process of winterizing a Sea-Doo step by step.

Before we dive in, gather your winterization kit, which should include Sea-Doo's specific winterization formula, a fuel stabilizer, a grease tube, a prop removal tool, and protective cover. Now, let's get started!

Pre-Winter Preparation

Before you begin winterizing, ensure your Sea-Doo is clean and has been rinsed off to remove any salt, sand, or dirt that could cause corrosion or damage over the winter months.

AD
How to Winterize Your Sea Doo 4-TEC Jet Ski Personal Watercraft
How to Winterize Your Sea Doo 4-TEC Jet Ski Personal Watercraft
How to Winterize Sea-doo GTI SE 130 Jet Ski to Save Money DIY - Not Sealed
How to Winterize Sea-doo GTI SE 130 Jet Ski to Save Money DIY - Not Sealed
How to Winterize Your PWC - Sea-Doo
How to Winterize Your PWC - Sea-Doo

Next, check your owner's manual for specific instructions on your Sea-Doo model. While the steps below apply to most Sea-Doo PWCs, there may be model-specific instructions to follow.

Engine Care

Start by adding a fuel stabilizer to your Sea-Doo's gas tank to prevent fuel from breaking down and damaging your engine over the winter. Use a stabilizer with an alcohol base to protect the fuel system from rust and deposits. Make sure to run the engine for a few minutes to ensure the stabilizer reaches all parts of the fuel system.

Helpful Jet Ski Tips: How To Flush Engine After Riding
Helpful Jet Ski Tips: How To Flush Engine After Riding
How to Winterize a Jet Ski for Storage | Extra Space Storage
How to Winterize a Jet Ski for Storage | Extra Space Storage

After running the engine, allow it to cool down before adding the Sea-DooSpecific winterization formula. Locate the winterization port on your engine (consult your owner's manual if needed) and add the recommended amount of formula. Run the engine for about 30-60 seconds to ensure the formula reaches all parts of the engine.

Lubrication and Maintenance

Greasing fittings is an essential step in winterizing your Sea-Doo. Use a grease tube to lubricate the steering pivot points, the cavitation plate, and the trim and tilt bellows. Be sure to remove any excess grease to avoid attracting dirt and debris.

AD

Inspect the enclosed belt under the hood and, if necessary, lubricate it with a small amount of marine formula grease. Check the tension of the belt and adjust it according to your owner's manual if needed. Finally, clean the coolers and ensure they're free of debris to promote proper cooling when you kick off the new riding season.

Hull and Interior Care

Maintaining the hull and interior of your Sea-Doo is just as important as caring for the engine. Start by inflating the floataions if they're not already inflated, as this will help support the weight of the PWC and prevent stress on the hull during storage.

Clean the entire PWC, paying special attention to the hull, where scrapes or scratches can become more noticeable due to improper storage. Apply a good-quality wax to protect the gel coat from ultraviolet rays and other environmental damage. Remember to wax the entire PWC, including the bottom section beneath the waterline, to provide comprehensive protection.

AD

Storage Prep

Before storing your Sea-Doo, change the oil and filter. Fresh oil will protect the engine better than old oil left sitting over the winter. Consult your owner's manual for the recommended oil type and amount, and follow the proper draining and replacement procedures.

Drain the water from the cooling system to prevent freezing and potential damage to the engine. Make sure to leave the drain plug out to allow any remaining water to drip out. Also, remove the spark plugs and apply a small amount of oil to the threads to protect them from corrosion.

Shrink-Wrapping and Covering

Once you've finished winterizing, it's time to protect your Sea-Doo from the elements during storage. One option is to shrink-wrap your PWC, which provides a tight, waterproof barrier. However, this method can be costly and time-consuming. An alternative is to use a high-quality, waterproof cover designed specifically for Sea-Doo PWCs.

AD

Secure the cover tightly to prevent it from blowing off during high winds. For added protection, consider placing a few blankets or tarps underneath the cover to provide extra padding and absorb any condensation that may form. Store your Sea-Doo in a dry place, away from direct sunlight and preferably indoors, but if outdoor storage is necessary, make sure the area is well-ventilated to prevent condensation buildup.

Now that your Sea-Doo is properly winterized and stored, you can eagerly await spring's arrival to hit the water with confidence. By following these steps, you've taken the necessary precautions to ensure your PWC is ready for the next season of fun and adventure. Happy winterizing!

AD