how to turn on old radiator

Resurrect Your Heater: How to Turn On an Old Radiator

By Emily Smith
AD

Have you recently moved into an older home and found yourself puzzling over some traditional cast-iron radiators? Well, you're not alone. These heating systems have been around for over a century and while they may look daunting, knowing how to turn on an old radiator is a valuable skill to have.

The process involves understanding a few basic components and then following a simple series of steps. Let's dive into the world of vintage radiators and get them warming up your space in no time!

Understanding Your Radiator's Components

Before we starting turning on the heat, let's familiarize ourselves with the key parts of an old radiator. The main components you'll need to know are:

AD
How to turn a radiator off
How to turn a radiator off
Paint a Radiator Like a Pro—No Experience Needed
Paint a Radiator Like a Pro—No Experience Needed
Preparation is key when painting radiators
Preparation is key when painting radiators
  • Valve: This controls the flow of water into the radiator.
  • Lockshield Valve: This regulates the water flow and helps balance the system.
  • Feather Key: A small, Y-shaped tool used to open and close the valves.

Identifying Valves

Radiators typically have two valves - the lockshield valve (usually at the top) and the main control valve (at the bottom). The lockshield valve often has a plastic cap over it for protection. The control valve is the one you'll use to adjust the heat.

The control valve, also known as the TRV (Thermostatic Radiator Valve), has a head that rotates to open or close. Some have a numbered scale to help you adjust them precisely. Others simply open and close with quarter turns. You'll see a red or blue indicator on the head that shows the valve's direction - clockwise turns to close, and counterclockwise to open.

Turn your radiator into a humidifier
Turn your radiator into a humidifier
a radiator with the words let's do it how to make a radiator heater attractive
a radiator with the words let's do it how to make a radiator heater attractive

Preparing Your Tools

Before you begin, you'll need to gather your tools. Apart from the feather key, you'll also need:

  • A wrench or adjustable pliers to loosen the valve handle.
  • A cloth or old towel to catch any drips or leaks.

Steps to Turn On an Old Radiator

Now that you're versed in the anatomy of your radiator and have all necessary tools, let's proceed with turning on the heat!

AD

Keep in mind, radiators get very hot, so ensure you're working safely by switching off the power at your system's main stopcock and allowing the water and pipes to cool down for at least 30 minutes before starting.

Opening the Valves

Locate the control valve at the bottom of your radiator. Use the wrench or pliers to unscrew the handle counterclockwise until you can see the brass stem. This is where you'll use your feather key.

Place one end of the Y-shaped tool on the brass stem and apply gentle, even pressure while slowly turning the other end counterclockwise. Keep turning until the handle is fully open or you've turned it to your desired setting on the numbered scale (usually around 1.5 to 2 on a typical scale).

AD

Checking for Leaks and Air Locks

Now, it's time to reopen the main water supply to your radiator. Head back to your stopcock and slowly turn the handle counterclockwise to start the water flow.

Monitor your radiator closely. If there's a leak, ensure it's minimal and can be fixed with a bit of PTFE tape or a new washer. If you hear banging or ‘knocking’ noises, you might have air in the system. This is common in old radiators and can be cleared by bleeding the radiator - a process that involves opening a small valve at the top (usually covered by a square brass plug) to let air out.

Adjusting the Lockshield Valve

Once your radiator is warm and your system is clear of air locks, the final step is to adjust your lockshield valve. This is typically left fully open during installation, but adjustment can help balance your system's water flow.

AD

Follow the same process as the control valve, using your feather key to open or close the lockshield valve. Close it if your radiator is too hot or open it if it's not warming up enough. Adjust by small turns until you achieve your desired temperature.

Safety Check

After adjusting your valves, take a moment to check that they're secure and there are no leaks. Monitor your radiator for a few hours to ensure it's heating evenly. If something isn't right, don't hesitate to call a professional plumber.

Turning on an old radiator may seem intimidating at first, but with a little patience and understanding of your system, you'll have your vintage heating unit purring like new in no time! Next time, turn that dial with confidence, and enjoy the warmth of history in your home.

AD