how to turn off oil change light jeep renegade

How to Turn Off Oil Change Light Jeep Renegade

By Ashley Martinez
AD

When the 'Change Oil' light appears on your Jeep Renegade, it's time to schedule a service appointment. However, if you're a DIY enthusiast, you might want to know how to reset the light after performing the oil change yourself. Here's a step-by-step guide to help you.

Before you get started, ensure you have the necessary tools and materials. You'll need a wrench to loosen the oil pan's drain plug, an oil filter wrench, a new oil filter, enough new oil for your Renegade (around 5.7 quarts), a funnel, and a drain pan. Also, familiarize yourself with your specific Renegade model's oil change process in the owner's manual.

Preparation

Before starting, find a safe, well-lit, and level area to perform the oil change. Let your engine run for about 15 minutes to warm up the oil for easier draining. Then, turn off the engine and allow the oil to drain back into the pan for about 30 minutes.

AD
How to Reset Oil Change on Jeep Renegade: Step-by-Step Guide
How to Reset Oil Change on Jeep Renegade: Step-by-Step Guide
How to Reset Oil Light Jeep Renegade: Step-by-Step Guide
How to Reset Oil Light Jeep Renegade: Step-by-Step Guide
How to Turn Off Oil Change Light Jeep Renegade: Step-by-Step Guide - Ran When Parked
How to Turn Off Oil Change Light Jeep Renegade: Step-by-Step Guide - Ran When Parked

Once cooled, locate the oil pan at the bottom of your engine and place your drain pan underneath it. Use your wrench to loosen and remove the oil pan's drain plug. Allow the oil to drain completely, this could take up to 10 minutes.

Removing and Replacing the Oil Filter

Now that the oil is drained, locate your oil filter, usually attached to the bottom of the engine with a strap. Using your oil filter wrench, turn the filter counterclockwise to remove it. Make sure to wipe the mounting surface clean.

Reset an Oil Change Light [Easy Steps for American-Made Vehicles]
Reset an Oil Change Light [Easy Steps for American-Made Vehicles]
How to Reset the Oil Change Light in a Car
How to Reset the Oil Change Light in a Car

Before installing the new filter, apply a small amount of new oil to the gasket, insertion area of the filter, and the gasket ring. Then, hand-tighten the new filter onto the engine's mounting surface by turning it clockwise, usually about one-and-a-half to two turns after the filter reaches resistance.

Adding New Oil

Replace the oil pan's drain plug, ensuring it's clean and properly torqued to the manufacturer's specification ( usually around 25 lb-ft). Take your funnel and begin adding the new oil through the opening in the oil case, above the oil pan.

AD

When adding the oil, keep an eye on the dipstick. The goal is to reach the 'FULL' mark on the dipstick when the vehicle is level and the engine is cool. Most Jeep Renegades take around 5.7 quarts of oil, but it's always best to check your owner's manual for the exact quantity for your specific model.

Resetting the 'Change Oil' Light

Once you've successfully changed the oil, it's time to reset the light. First, locate the 'Service' button on your instrument panel. It's usually on the right side of the steering wheel. Press and hold this button for around 10 seconds until the 'Service Oil Change' message disappears from the display.

Now, with the 'Service Oil Change' message no longer showing, press the 'OK' button once. The light should now be reset. If it doesn't, don't worry - the light is designed to turn off once you drive 500 miles after the oil change, so a short test drive should help.

AD

And that's it! By following these steps and using the right tools, you can effectively change your Jeep Renegade's oil and reset the 'Change Oil' light at home, saving you time and money. Always remember to dispose of used oil responsibly, usually at a certified collection center. Now, enjoy your driving peace of mind, knowing your Renegade is well-maintained and ready for the miles ahead.

AD