how to thread a janome new home sewing machine

How to Thread a Janome New Home Sewing Machine

By Kevin Lee
AD

If you're new to sewing or have recently purchased a Janome New Home sewing machine, threading might seem like an intimidating task. Fear not! With this comprehensive guide, you'll master the art of threading your Janome New Home sewing machine in no time. Let's dive right in.

Before we start, ensure you have the following items at hand: your sewing machine, a spool of thread, a thread stand, and a light source (optional, but helpful for seeing through the thread holes). Now, let's prepare your machine and thread.

Preparing Your Janome New Home Sewing Machine

Begin by placing your sewing machine on a sturdy, well-lit table. Don't forget to plug it in and remove the presser foot, if attached. Next, locate the thread stand (also known as a thread standup) on the side of your machine. If it's not in place, gently push it up to the ready position.

AD
How to thread a Janome sewing machine
How to thread a Janome sewing machine
How to Thread a Janome Sewing Machine
How to Thread a Janome Sewing Machine
How To Thread a Sewing Machine | Sewing Tutorial for Beginners | Janome DC6030/DKS30 #Shorts #Sewing
How To Thread a Sewing Machine | Sewing Tutorial for Beginners | Janome DC6030/DKS30 #Shorts #Sewing

Your Janome New Home sewing machine comes with two spool pins. Attach your spool of thread to the forward-facing spool pin, allowing the thread to hang naturally. Make sure the thread is not tangled, and the spool is secured properly. If the thread is twisted, carefully untwist it to avoid future tangles.

Threading the Upper Tension Disc

The upper tension disc plays a crucial role in maintaining even tension as the thread feeds through your machine. To thread it, follow the path of the thread guide from the spool, around the upper tension disc, and up towards the take-up lever.

How to Thread a Janome Sewing Machine tutorial with Close Ups
How to Thread a Janome Sewing Machine tutorial with Close Ups
Janome Sewing Machine Threading
Janome Sewing Machine Threading

From the spool, lightly drop the thread onto the thread stand and guide it up to the tension disc. Insert the thread into the threading hook found on the right side of the disc, then pull it gently through the hook and onto the disc's groove. Once you've threaded the disc, lift the take-up lever and pull the thread up from underneath, guiding it through a loop on the lever.

Threading the Take-Up Lever and Bobbin Race

The take-up lever facilitates the supply of thread from the spool to the needle. After threading the upper tension disc, guide the thread up and over the take-up lever, making sure it rests in the lever's threading hook and follows the groove towards the bobbin case.

AD

Now, move the thread towards the bobbin case, located below the needle plate. Carefully insert the thread into the slot in the bobbin case (the thread should face the needle). This slot, known as the bobbin race, guides the thread down towards the bobbin itself.

Threading the Bobbin and Needle

To thread the bobbin, pull the thread tail through the bobbin's center hole and wind it around the bobbin in a clockwise direction (from the left to the right, as seen from the top). Aim for about 4-5 loops, leaving an approximately 2-inch tail free.

Once the bobbin is threaded, snip the excess thread, leaving a minor tail of about ¼ inch to ½ inch. Insert the bobbin into the bobbin case, ensuring it's facing the correct direction (the thread should be protruding through the slot you previously threaded). Secure the bobbin case into your machine by screwing the handwheel to the right. You'll see the screw holes on the side of the machine.

AD

Threading the Needle

Before threading the needle, make sure it's lint-free and there's no broken thread inside. Pull the thread up through the needle, ensuring it's the correct side (the needle has an 'L' or 'R' marking, indicating the direction the thread should face within the needle). Bring the thread down towards the sewing surface, allowing it to drop freely onto the fabric below.

Raise the presser foot and set your machine to a handwheel operation. Turn the handwheel slowly in a clockwise direction, watching as the needle moves up and down. Check that the thread is feeding through correctly and that there are no tangles or impede the thread's path.

Testing Your Threading

To test your threading, lower the presser foot and set your machine to the normal sewing position. Bring the needle to its highest point and commanding it to one or two stitches. If your machine has operated successfully, you should see a stitch on your fabric below. Finally, raise the presser foot, turn your machine off, and unplug it.

AD

Congratulations! You've successfully threaded your Janome New Home sewing machine. Embrace your newfound skill, and happy sewing!

AD