how to test starter solenoid relay

How to Test a Starter Solenoid Relay

By Brian Miller
AD

When your car won't start, a faulty starter solenoid relay is often to blame. Testing this component is crucial to diagnose the problem, saving you time and money. Here's a comprehensive guide on how to test a starter solenoid relay, ensuring you understand each step and any necessary tools.

Before we dive in, let's ensure you're familiar with the starter solenoid relay basics. This device is an electrical switch that controls power to the starter motor. It's usually found on the driver's side of the engine, near the starter motor itself. Now, let's learn how to test it.

Preparation and Safety Precautions

Before starting, ensure your car is parked on a level surface and the parking brake is engaged. Turn off the ignition and remove the keys. Wear safety glasses, and use insulated tools to avoid electrical shocks.

AD
the wiring diagram for an electric vehicle that is not in use, it shows how to wire
the wiring diagram for an electric vehicle that is not in use, it shows how to wire
How To Test a Relay (and How Relays Work) - in 8 minutes
How To Test a Relay (and How Relays Work) - in 8 minutes
How to test your starter motor & solenoid - Starter troubleshooting
How to test your starter motor & solenoid - Starter troubleshooting

You'll need the following tools: a multimeter, aု�ausekey wire (also known as jumper wires), and a repair manual for your specific vehicle make and model. The manual will provide a wiring diagram, which is essential for accurate testing.

Understanding the Wiring Diagram

The wiring diagram shows the relay's connector, with pins labeled for each function. Typically, the relay has four pins: battery power (+B), ground (-B), ignition (I), and starter motor (S).

How to Test a 5 Pin Relay with a Multimeter (Guide)
How to Test a 5 Pin Relay with a Multimeter (Guide)
How to Test a Relay? Troubleshooting SSR & Coil Relays by DMM
How to Test a Relay? Troubleshooting SSR & Coil Relays by DMM

Familiarize yourself with these points to accurately perform the test:

  • Battery power (usually red or brown wire)
  • Ground (usually black or white wire)
  • Ignition (usually yellow, green, or brown wire)
  • Starter motor (usually thick, stiff wire)

Testing the Starter Solenoid Relay

Once you've located the relay and understood its wiring, follow these steps to test it using a multimeter:

AD
  1. Set your multimeter to measure resistance. This step is crucial as you'll be checking the internal continuity of the relay.
  2. Disconnect the relay's connector and separate the wires.
  3. Touch the multimeter probes to the battery power (B+) and ground (-B) pins on the relay's connector. If the relay is functioning correctly, you should see a reading of zero ohms. If there's high resistance or a reading of infinity, the relay is faulty and needs replacing.
  4. Repeat the resistance test between the battery power (B+) and ignition (I) pins. A good relay should also show zero ohms.
  5. Now, test the starter motor (S) pin with the battery power (B+) pin. Again, you should see a reading of zero ohms if the relay is functioning correctly.

The resistance test helps determine if the relay's internal contacts are shorted or open. If any reading is other than zero ohms, the relay is faulty. However, you should also perform a continuity test to be sure.

Continuity Test

A continuity test checks if electricity can flow through the relay's coil and contacts, simulating the relay being closed. Follow these steps:

  1. Set your multimeter to test for continuity (usually indicated by a sound, such as a beep, or a display of "OL" for open loop).
  2. Touch one probe to the battery power (B+) pin and the other to the ignition (I) pin. If the relay is functioning correctly, the multimeter should beep or show a resistance below 5 ohms.
  3. Repeat the test between the ignition (I) pin and the starter motor (S) pin, with the same expected result.

If the relay fails either the resistance or continuity test, it's faulty and should be replaced. Always consult your repair manual for detailed steps on removing and reinstalling the relay.

AD

Troubleshooting Common Issues

Sometimes, the problem isn't with the relay itself but with its connections or the control circuit. Here are some common issues to troubleshoot:

Corroded or Loose Connections

Inspect the relay's connector and its wires for corrosion or�ြreprocessorrelation. A poor connection can cause intermittent problems, making the car seem unpredictable. Clean the connections with emery cloth or a wire brush, and apply a suitable connector cleaner or grease.

Similarly, check for loose or damaged wires. Wiring diagrams can help identify the correct wire color and size. Repair or replace damaged wires as needed.

AD

Control Circuit Issues

Sometimes, the problem lies in the control circuit. Check for blown fuses or poor connections elsewhere in the ignition circuit. Ensure the starting switch (ignition key or push-button start) and its wiring are in good condition.

Additionally, ensure the car's computer and its wiring aren't causing issues. Consult your repair manual for detailed information on the ignition circuit, including fuses, relays, and sensors.

If you've tested the starter solenoid relay and found it functional, but your car still won't start, further diagnosis is needed. Inspect the starter motor, battery, and associated wiring for faults.

While this guide provides a thorough overview, always consult your vehicle's repair manual for specific procedures tailored to your make and model. Regular maintenance and prompt diagnosis of any electrical issues can keep your car running smoothly.

Testing a starter solenoid relay might seem daunting, but with the right tools and knowledge, it can be a manageable task. By understanding your vehicle's wiring diagram and performing the necessary tests, you can confidently diagnosis and repair potential problems. Happy wrenching!

AD