how to test a relay switch

How to Test a Relay Switch

By Kevin Robinson
AD

Ever experienced dimming or flickering lights, or a suddenly quiet workshop because of a faulty relay switch? These electrical components are unsung heroes, controlling power in our homes and workplaces, but they're not immune to wear and tear. Here's a comprehensive, step-by-step guide on how to test a relay switch to keep your electrical systems running smoothly.

Before we dive into the specifics, let's clarify what we're dealing with. A relay switch is an electrically operated switch that can be used to control power in a circuit. It's essentially an electronic switch with a small coil that activates a set of contacts, allowing or breaking electrical flow. Whenever you're working with electricity, always remember to prioritize safety first.

Understanding Your Relay Switch

A relay switch has a coil, contacts, a contact set, and sometimes a diode across the coil. Understanding these components is crucial before you start testing. The coil is where the control voltage is applied. When this voltage exceeds a certain value, the contacts move, completing or breaking the circuit you're controlling.

AD
How To Test a Relay The Easy Way
How To Test a Relay The Easy Way
Relay Testing Checklist for DIYers
Relay Testing Checklist for DIYers
How to test a relay with a multimeter
How to test a relay with a multimeter

Relays can be further categorized into different types based on their function - changeover, normally open, normally closed, single pole single throw (SPST), and more. The specific type determines how you'll test it, so ensure you understand this before proceeding.

Visual Inspection

Before you test your relay, give it a visual once-over. Check the relay's metal contacts for any signs of corrosion or damage. If the contacts are burned, blackened, or sheer, replace the relay immediately. Also, look for signs of heat damage around the relay's coil - this could indicate an overheating problem.

an electrical wire is being hooked up to the wall by someone's hand and wires are plugged in
an electrical wire is being hooked up to the wall by someone's hand and wires are plugged in
How To Test a Relay (and How Relays Work) - in 8 minutes
How To Test a Relay (and How Relays Work) - in 8 minutes

Next, check the coil's terminals for any loose or broken connections. Tighten the screws if necessary, but be careful not to strip the threads. If the coil or its connections are damaged, the relay may need replacing.

Using a Multimeter to Test Coil Resistance

Once you've done a visual check, it's time to get out your multimeter. The coil in a relay is essentially a resistor, so you can check for continuity or resistance. Set your multimeter to the lowest ohm setting (usually denoted by a sideways 'Ω').

AD

Touch one probe to each of the coil's terminals. The multimeter should display a relatively low resistance reading, typically between 500 ohms and 5 kilohms, depending on the relay's specifications. If the reading is much higher, or your multimeter shows no continuity (OL or ∞), the coil is likely faulty.

Testing the Contacts

Now that you've checked the coil, it's time to test the contacts. There's always a risk of energizing the contacts when they're closed, so ensure your main supply is switched off before testing.

Avoid touching the relay's contacts directly while testing. If they're already closed, you could experience an electric shock. Instead, use your multimeter to test for continuity across the contacts when the coil is energized and when it's not.

AD

Manual Contact Test

If your relay has an accessible armature or lever, you can manually move the contacts. This is useful for visual and SPST relays. By pulling or pushing the lever, you should hear a clicking sound as the contacts switch state. If there's no click, or the contacts don't appear to move, the relay may be faulty.

Again, be careful not to touch the contacts directly. If you must, ensure the relay and your hands are clean to prevent shorting the contacts. Also, never use the relay as a switch - this can cause arcs that can damage both the relay and the contacts you're testing.

Using a Digital Multimeter

To test the contacts using a multimeter, set it to the continuity setting (usually denoted by a diode symbol ['D'] or a sound wave). Touch the probes to the contacts. When the coil is energized, your multimeter should show continuity (beep) for closed contacts and no continuity (silence) for open contacts.

AD

Remember to switch your multimeter to resistance mode to check for any leakage current between open contacts. There should be high resistance (almost infinity) between them. If you read a low resistance (even at the highest ohm settings), the contacts aren't fully open, and the relay may need replacing.

After testing, always remember to double-check your relay is correctly seated and securely connected. If it's not steady or vibrates when it clicks, it might be a sign of improper mounting or a faulty relay. Finally, always ensure your relay is the correct type and rating for your intended use, and follow the manufacturer's guidelines for safe operation.

Testing a relay switch might seem daunting at first, but with a systematic approach and a thorough understanding of the components involved, it's a task even DIY enthusiasts can handle. Always remember to prioritize safety, check your work, and don't hesitate to replace a suspect relay.

AD