how to test a motorcycle coil

Motorcycle Coil Test: Easy DIY Check-up Guide

By William Hernandez
AD

Testing a motorcycle's ignition coil is a crucial aspect of motorcycle maintenance, ensuring your bike's engine performs at peak efficiency and safety. This article guides you through the process, focusing on safety, required tools, step-by-step procedures, and troubleshooting tips. Let's dive in.

Before we start, remember that working on a motorcycle's electrical system can be dangerous. Always ensure the bike is off, and disconnect the negative battery terminal to prevent short circuits. Safety first! Now, let's get our tools ready.

Gathering Necessary Tools

Before you begin, gather all the required tools. This will not only save time but also ensure you can complete the task safely and efficiently.

AD
How To Test Motorcycle, ATV & UTV Ignition Coils
How To Test Motorcycle, ATV & UTV Ignition Coils
How to Test a Motorcycle Coil with a Battery | Easy DIY Guide
How to Test a Motorcycle Coil with a Battery | Easy DIY Guide
How To Test And Troubleshoot Ignition Coils - Hunker
How To Test And Troubleshoot Ignition Coils - Hunker

Here's a list of tools you'll need:

  • A multimeter
  • Voltage leads
  • Rubber gloves
  • Socket wrenches (depending on your motorcycle's model)

Understanding Your Multimeter

A multimeter is an invaluable tool for testing electrical components. It measures voltage, current, and resistance. For this task, we'll use the continuity and resistance settings.

OAS - How to Test Pickup Coil This coil sends the spark signal to your CDI — no spark or hard starting? Check this first! 🔹 110–160 Ω = Good 🔹 < 110 Ω = Short circuit 🔹 > 160 Ω = Open circuit / broken wire #KnowYourWiring #mechanicguide #motorcycleparts | Facebook
OAS - How to Test Pickup Coil This coil sends the spark signal to your CDI — no spark or hard starting? Check this first! 🔹 110–160 Ω = Good 🔹 < 110 Ω = Short circuit 🔹 > 160 Ω = Open circuit / broken wire #KnowYourWiring #mechanicguide #motorcycleparts | Facebook
three different types of electrical devices are shown in this diagram, with instructions for how to use them
three different types of electrical devices are shown in this diagram, with instructions for how to use them

If you're unfamiliar with your multimeter, consult the instruction manual. Understanding its functions and controls is key to accurate results.

Preparation: Checking Your Bike's ElectricalSystem

Before diving into the coil itself, it's wise to check the motorcycle's electrical system. Locate the ignition coil, usually near the top of the engine.

AD

Remove any covers or wires connected to the coil. Ensure the engine is off and the battery is disconnected. Now you're ready to test.

Testing the Ignition Coil

Properly testing the ignition coil involves two primary steps: checking resistance and inspecting the coil's output. Both tests are crucial for accurate results.

Before you proceed, ensure all wires and connections are clean and dry to prevent false readings.

AD

Checking the Ignition Coil's Resistance

Resistance testing is a basic diagnostic to check the coil's internal condition. Here's how:

  1. Set your multimeter to the lowest ohms scale (usually 200 or 2k ohms).
  2. Touch one lead to the coil's primary terminal and the other to the secondary terminal.
  3. Record the resistance reading. Compare it to your motorcycle's specifications. Resistance should be within the given range (e.g., 0.5 to 3 ohms).

Inspecting the Coil's Output

Testing the coil's output is more involved but provides a fuller picture of its condition. You'll need a spark plug, spark plug wire, and a helper.

Here's a step-by-step guide:

AD
  1. Reattach the spark plug wire and the connector to the ignition coil.
  2. Insert a spark plug into the cylinder, but don't screw it in. Leave it just touching the head.
  3. Ask your helper to crank the engine while you observe the spark plug.
  4. You should see regular sparking. A healthy coil will produce a steady, semasa spark.

Troubleshooting Common Issues

If your coil tests faulty, don't rush to replace it. Here are some common issues to check first:

Inspect the coil mounting hardware for cracks or damage. Loose or damaged hardware can cause readings. Also, check the coil's connectors and cables for signs of wear or damage.

Testing the Coil's Insulation

Before replacing the coil, perform a simple resistance test to check the insulation:

  1. Set your multimeter to measure resistance (ohms).
  2. Touch one lead to the coil's body and the other to the center of the spark plug wire terminal.
  3. You should see a high resistance reading (around 1 megohm or above). If the reading is low, it indicates poor insulation.

Testing the Wiring Harness

Faulty wiring can cause coil-related problems. Check the wiring harness for fraying, breaks, or other damage. Use a visual inspection and resistance testing to diagnose issues.

Congratulations, you've successfully tested your motorcycle's ignition coil! Regular testing is key to maintaining your bike's performance and safety. Enjoy the ride, and stay safe on the roads.

AD