how to test a generac generator

Busting Amps: A Comprehensive Guide to Testing Your Generac Generator

By Matthew Harris
AD

Generac generators are essential for ensuring a steady power supply during power outages. To guarantee your Generac generator is in optimal condition, you need to regularly test it. Today, we'll guide you through a comprehensive, step-by-step process on how to test a Generac generator effectively.

Before we begin, remember that safety is paramount when handling generators. Always follow the manufacturer's instructions, and ensure the generator is off before you start any testing.

Preliminary Inspection

Before you conduct any tests, perform a visual inspection of your Generac generator. Check for any signs of damage or wear and tear. Look out for faded or frayed wires, corroded parts, or any visible leaks.

AD
Using your Generator.....what can you really run with it?
Using your Generator.....what can you really run with it?
Generac Generator Starts Then Dies: What to Check First?
Generac Generator Starts Then Dies: What to Check First?
How to Read Generator Specs Before You Buy
How to Read Generator Specs Before You Buy

This step might seem rudimentary, but it's crucial. A thorough visual inspection can help you identify potential issues before they escalate into significant problems.

Generator Fuel System Check

A Generac generator relies on fuel to run. The first step in testing your generator is to ensure its fuel system is working correctly. Start by checking the fuel gauge. It should display a full tank if your generator is in good working condition.

A SIMPLE Onan Generator Fuel Pump Test and Replacement Tips
A SIMPLE Onan Generator Fuel Pump Test and Replacement Tips
Generac Evolution Maintenance Reset / Dealer Menu
Generac Evolution Maintenance Reset / Dealer Menu

Fuel Sender Unit

The fuel sender unit transmits information about the fuel level to the gauge. If the gauge is indicating an incorrect fuel level, the unit might be faulty. Test the fuel sender unit by disconnecting its wiring harness and measuring the resistance across its pins using a multimeter.

Compare your readings to the manufacturer's specifications. If the resistance is significantly different, you might need to replace the fuel sender unit.

AD

Fuel Pump

Next, test the fuel pump. With the ignition switched off, disconnect the fuel pump's wiring harness. Connect a multimeter set to continuity mode to the pump's terminals. If the pump is working correctly, the multimeter should show a continuity beep when you turn the ignition on.

If there's no beep, replace the fuel pump. Also, ensure there's no blockage in the fuel lines by disconnecting them and checking for any debris or impurities.

Generator Electrical System Check

After checking the fuel system, let's move on to the electrical system. First, test the battery. Ensure it's in good condition and fully charged. You can do this by measuring its voltage using a multimeter.

AD

If the voltage is low, recharge or replace the battery. Next, test the battery's charging system. Start your generator and let it run for about 15 minutes. After turning it off, measure the battery's voltage again. It should have increased, indicating that the charging system is working correctly.

Generator Starter Motor

The starter motor initiates the generator's operation. To test it, connect a multimeter set to continuity mode to the starter motor's terminals. If the motor is in good condition, you should hear a continuity beep when you turn the ignition on.

If there's no beep, try tapping the starter motor gently while the ignition is on. If the motor runs, the issue might be with the ignition switch or the wiring. If not, you'll need to replace the starter motor.

AD

Generator Control Module

The generator control module (GCM) manages your generator's operation. To test it, disconnect the GCM's wiring harness and then reconnect it while your generator is off. If your generator starts and runs normally, the GCM is functioning correctly.

However, if your generator doesn't start, there might be an issue with the GCM. Try resetting it by disconnecting its battery connection, waiting for about 30 seconds, and then reconnecting it.

Generator Power Output Check

Finally, test your generator's power output. Start by connecting a non-responsive load, like a lamp or a small appliance, to the generator's outlets. The generator should start and maintain a consistent speed.

Next, connect a responsive load, such as power tools or motors. These loads draw more power and should cause the generator's speed to vary slightly. If everything works as expected, your generator's power output is functioning correctly.

Regular testing is key to maintaining your Generac generator's performance. So, don't wait for an emergency to find out if your generator is in good working condition. Stay proactive and test your generator regularly to ensure power reliability when you need it most.

AD