how to take apart a weed wacker

Easy Weed Wacker Disassembly: A Step-by-Step Guide

By Jessica Jackson
AD

Taking apart a weed wacker, also known as a string trimmer, might seem daunting at first, but with the right steps and a little patience, you'll be disassembling it like a pro in no time. Understanding the process can also help you maintain or repair your weed wacker more effectively. Let's dive into a step-by-step guide to help you take apart your weed wacker safely and efficiently.

Before you begin, ensure you have the following tools: a Phillips screwdriver, a flathead screwdriver, pliers, and possibly a hammer or a rubber mallet. Safety glasses are also recommended to protect your eyes during the disassembly process.

Preparation and Initial Steps

Before you start taking apart your weed wacker, make sure it's unplugged or the battery is removed to prevent any accidental starts. Additionally, lay out a drop cloth or old towel to prevent losing any small parts in the grass.

AD
Fastest Way to String Weed Eater
Fastest Way to String Weed Eater
How To Convert A String Trimmer To A Brush Cutter - Hunker
How To Convert A String Trimmer To A Brush Cutter - Hunker
String trimmer weed eater wacker will not start, diagnosis and EASY repair fix free!
String trimmer weed eater wacker will not start, diagnosis and EASY repair fix free!

Once you're set up, begin by removing any coverings or shrouds that protect the inner workings of the weed wacker. You can typically pull these off by hand, but you might need to use pliers to tug on any stubborn clips or ties.

Removing the Guard and Spoiler

The guard and spoiler are designed to protect you and the weed wacker from thrown debris. To remove them, look for Phillips screws on the underside of the weed wacker. These usually hold the guard in place. Using your Phillips screwdriver, unscrew and remove these, taking note of their positon as you might need to place them back in the same order when reassembling.

How To Restring Your Toro Flex Force Weed Wacker In Under a Minute!
How To Restring Your Toro Flex Force Weed Wacker In Under a Minute!
How To Restring A Weed Eater - Hunker
How To Restring A Weed Eater - Hunker

Once the screws are out, use your fingers or pliers to pull the guard and spoiler off. They might be snug, so you may need to gently work them loose with a screwdriver or use a hammer or rubber mallet to tap them slightly.

Taking Off the Covers

The next step is to remove the plastic covers that hide the inner mechanics of the weed wacker. These are usually held in place by small plastic clips or screws. Use a flathead or Phillips screwdriver to remove any screws, and use pliers to carefully pry off any clipped covers.

AD

If you're struggling with a stubborn clip, you can use a flathead screwdriver to gently pry the clip open, or use a small, flat object like a coin to slowly push the clipped cover off. Be careful not to damage any parts in the process.

Disassembling the Mechanics

With the cosmetics of your weed wacker removed, you'll now have access to the internal parts. Start by removing any visible screws from the exterior. If there are no visible screws, check for any door-like panels or covers that might hide additional screws.

Large weed wackers might have a airshed or a thin metal plate that covers the engine and other internal components. Remove any screws holding this in place and gently lift it off. You might need to bend the weed wacker's handle upwards to provide enough room to remove the plate.

AD

Removing the Engine and Engine Plate

The engine plate, or crankcase, is the large, silver or black part that houses the engine. To remove it, first, locate the fuel line and the spark plug wire. Use pliers to carefully remove the connectors at both ends, ensuring you don't lose any small pieces.

Next, use a wrench to loosen the engine mounting bolts. These are often located beneath the weed wacker's handle and at the top of the engine. With the bolts loose, you should be able to lift the engine out. If it's stuck, gently tap it with a hammer or rubber mallet until it comes free. Once the engine is out, set it aside.

Separating the Cables and Sensors

The final step in disassembling your weed wacker involves removing any remaining cables, sensors, and small parts. First, disconnect any wires connected to the trigger or speed control. These can usually be unplugged by hand, but you might need to use pliers for particularly stubborn connections.

AD

Next, inspect the weed wacker's handle and body for any sensors or additional components. These might include an on/off switch, a speed control dial, or a cable release for the line spool. Carefully remove any screws holding these in place and set the components aside.

Congratulations! You've successfully taken apart your weed wacker. With practice, you'll find that each subsequent disassembly is faster and easier. Regular maintenance and timely part replacements will help extend the life of your weed wacker and keep it running smoothly. Now that you're a pro at taking it apart, don't forget to familiarize yourself with the reassembly process to ensure you put everything back in the right place. Happy weeding!

AD