how to start husqvarna blower

How to Start Your Husqvarna Blower: A Step-by-Step Guide

By Thomas Jackson
AD

Starting your Husqvarna blower can be a breeze once you're familiar with the process. follow these steps to get your equipment up and running efficiently, ensuring a pleasant and productive user experience.

Before we dive into the starting process, safety should always be your top priority. Put on appropriate protective gear, including gloves, safety glasses, and ear protection. Then, ensure you're in a clear, safe area away from people and pets.

Preparing Your Husqvarna Blower

Preparation is key to a smooth starting process. First, inspect your blower for any obstructions or damage. Check the air filter, as clogging or damage can affect performance and engine life. Clean or replace it as needed.

AD
How To Start A Husqvarna Leaf Blower – Storables
How To Start A Husqvarna Leaf Blower – Storables
How to Start a Husqvarna Snow Blower: A Step-by-Step Guide
How to Start a Husqvarna Snow Blower: A Step-by-Step Guide
How to Start a Husqvarna 580BF Blower with Rick Pantano owner of Pantano Power Equipment
How to Start a Husqvarna 580BF Blower with Rick Pantano owner of Pantano Power Equipment

Next, check the fuel level and ensure you're using the recommended fuel type – unleaded gasoline with an octane rating of 90 or higher, mixed with 2-cycle oil in a 50:1 ratio. Store fuel safely and not for more than 30 days to prevent degradation.

Locating the Start/Stop Switch

Familiarize yourself with your Husqvarna blower's controls. The start/stop switch is typically on the handle, with 'on' and 'stop' positions marked. For many models, you'll also see an 'on' position for the choke, which is used when starting the blower.

Husqvarna Pto Switch Wiring Diagram
Husqvarna Pto Switch Wiring Diagram
Husqvarna vs. Stihl Blowers – Tool Review & Comparison
Husqvarna vs. Stihl Blowers – Tool Review & Comparison

Other notable switches include the throttle, speed control, and cruise control (on certain models). Understanding these controls will help you navigate through the starting process and ensure optimal operation.

Positioning Your Blower

When starting your blower, ensure it's on a flat, stable surface. It's best to start it with the blower tube facing away from you, providing clearance and reducing the risk of dirt and debris being blown back onto you. Additionally, keep the muffler pointing downwards to avoid burns from hot exhaust.

AD

For safer and more efficient starting, it's recommended to have your Husqvarna blower connected to a ground fault circuit interrupter (GFCI) protected extension cord. This ensures protection against power surges and Electrical shock.

Starting Your Husqvarna Blower

Now that your blower is prepped and you're familiar with its controls, it's time to start it. Here's a step-by-step guide tailored to different Husqvarna blower models, with the general process being quite similar across the range.

The main differences lie in the specific choke position (either 'on' or 'start'), and whether your model has a primer bulb. These steps will cover both scenarios, making it universally applicable.

AD

Starting a Cold Blower

When starting a cold blower, the engine will require more fuel to ignite. Here's how to do it:

  1. Place the start/stop switch to the 'off' position.
  2. Move the choke to the 'on' position (or 'start' for some models).
  3. Press the primer bulb (if your model has one) slowly and repeatedly until it feels firm, then release it. Do this 3-5 times.
  4. Pull the starting rope firmly and quickly, adding more force towards the end of the pull. If your model has a start/stop switch with an 'on' position, pull the rope with the switch in the 'on' position.
  5. Once the engine starts, reduce the choke gradually until it reaches the 'run' position. Allow the engine to warm up for a few seconds before increasing the throttle for full operation.

Starting a Warm Blower

Starting a blower with a warm engine is generally easier and requires less fuel.

  1. First, ensure the start/stop switch is in the 'off' position.
  2. Then, move the choke to the 'on' position (or 'start' for some models) to provide additional fuel for the restart.
  3. Next, pull the starting rope firmly and quickly, following the same technique as starting a cold blower.
  4. Once the engine starts, gradually reduce the choke until it reaches the 'run' position.

Now that your Husqvarna blower is running smoothly, it's time to tackle those leaves and debris. Remember to take regular breaks, keep the blower maintained, and always prioritize safety above all else. Happy blowing!

AD
AD