how to size parallel conductors

Mastering Parallel Conductors: Expert Guide on Sizing

By Brian Lee
AD

Sizing parallel conductors is a critical step in electrical engineering, as it ensures the safe and efficient operation of electrical systems. It involves selecting conductors that can handle the required current while minimizing voltage drop. This guide will walk you through the process, helping you understand the key factors and calculations involved.

Before diving into the specifics, it's important to note that sizing parallel conductors differs from sizing a single conductor. Unlike a single conductor, where the current is constant throughout, each conductor in a parallel circuit carries only a portion of the total current. This distribution depends on the resistance of each conductor.

Understanding Current Distribution in Parallel Conductors

The current through each conductor in a parallel circuit is inversely proportional to its resistance. This means that a lower resistance conductor will carry more current than a higher resistance one, given the same voltage drop.

AD
Conductor Ampacity, Voltage Drop, and Line Losses Explained | Electrical Academia
Conductor Ampacity, Voltage Drop, and Line Losses Explained | Electrical Academia
the transisson line diagram for two different types of parallels, which are labeled in
the transisson line diagram for two different types of parallels, which are labeled in
Figure 8 Compression Ground Rod Connector 1" (2/0 Cable range)
Figure 8 Compression Ground Rod Connector 1" (2/0 Cable range)

In mathematical terms, the current (I) through each conductor is given by Ohm's Law (I = V/R), where V is the voltage across the parallel circuit, and R is the resistance of the conductor. Therefore, the ratio of currents through two parallel conductors is given by the ratio of their resistances (I1/I2 = R2/R1).

Resistance of Conductors

The resistance (R) of a conductor is given by the formula R = ρL/A, where ρ is the resistivity of the material, L is the length of the conductor, and A is its cross-sectional area. For practical purposes, the cross-sectional area is usually taken as the area of the conductor's circular cross-section, πr², where r is the radius.

Grounding Conductor Size Calculator — NEC 250
Grounding Conductor Size Calculator — NEC 250
Introduction to Inductors
Introduction to Inductors

Resistivity (ρ) is a property of the material and is constant for a given temperature. For copper, one of the most commonly used electrical conductors, ρ is approximately 1.72×10⁻⁸ ohm-meters at 20°C.

Cross-Sectional Area of Conductors

Given the resistance and resistivity of the conductors, and the length of the conductors, the required cross-sectional area (A) can be calculated using the formula A = ρL/R. This will give the minimum cross-sectional area required to keep the voltage drop within acceptable limits.

AD

Conductor sizes are standardized, so it's necessary to choose the nearest standard size that is equal to or larger than the calculated area. Using a larger size than necessary may seem wasteful, but it provides some safety margin against unforeseen increases in current or voltage.

Amperage and Voltage Drop

The total current (I) flowing through the parallel circuit is the sum of the currents flowing through each conductor. This total current should not exceed the conductor's ampacity, which is the maximum current that the conductor can carry safely.

The voltage drop (VD) across each conductor should also be within acceptable limits. For most applications, this is typically around 3% to 5% of the system voltage. The voltage drop can be calculated using Ohm's Law (VD = IR), where I is the current through the conductor and R is its resistance.

AD

Conductor Ampacity

The ampacity of a conductor is determined by its material, size, and environmental conditions. It's the maximum current that the conductor can carry without exceeding its maximum allowable temperature. Conductor ampacities are standardized and can be found in tables or charts.

When sizing parallel conductors, the entire circuit's current must be considered, not just the current through each conductor. To find the equivalent current-carrying capacity, the ampacities of the parallel conductors are added together. This is because the conductors in a parallel circuit share the total circuit current.

Conductor Selection

Once the required ampacity and cross-sectional area are known, the appropriate conductor size can be selected. This is typically done using a conductor sizing chart, which lists standard conductor sizes and their respective cross-sectional areas and ampacities.

AD

It's important to note that the selected conductor should not only meet the required ampacity and cross-sectional area, but also be compatible with the rest of the electrical installation. This includes considerations like voltage rating, application, and electrical environment.

Sizing parallel conductors requires a balance of electrical theory, practical application, and an understanding of standards and regulations. By carefully following the steps outlined above, you can ensure that your parallel conductors are safe, efficient, and compliant with all relevant codes and practices.

AD