how to sheetrock around a tub

Mastering Sheetrock Around a Tub: Pro Steps

By Andrew Clark
AD

Embarking on a home improvement project, such as installing sheetrock around a bathtub, can seem daunting, but with the right guidance, it's a task well within your reach. This comprehensive guide will walk you through the process step by step, ensuring a professional finish that not only enhances the aesthetic appeal of your bathroom but also maintains its functionality and safety.

Before you get started, it's crucial to understand that working around a bathtub requires special considerations. The proximity to water means you'll need to prioritize moisture resistance and proper ventilation. By following the steps below and using the appropriate tools and materials, you can achieve a successful outcome that will add value to your home.

Preparation: Gathering Supplies and Ensuring Safety

Before you begin, gather all the necessary supplies to ensure a smooth and efficient working process. You'll need sheetrock, joint compound, corner bead, drywall screws, tape measure, utility knife, straight edge, trowel, sandpaper or drywall sanding screen, safety glasses, and work gloves. Additionally, protect the floor and surrounding area with drop cloths to minimize cleanup later on.

AD
How to Waterproof a Tile Shower in a Tub Surround - Erin Zubot Design
How to Waterproof a Tile Shower in a Tub Surround - Erin Zubot Design
DIY Tile Tub Surround That Will Save You Money
DIY Tile Tub Surround That Will Save You Money
How I Installed a Beautiful Tile Tub Surround
How I Installed a Beautiful Tile Tub Surround

Safety is paramount when working with sheetrock. Wear appropriate safety gear, including a dust mask, to protect against inhaled drywall dust. Ensure there's adequate ventilation in the workspace, and be mindful of electrical outlets and plumbing when cutting the sheetrock.

Measuring and Cutting the Sheetrock

Begin by turning off the electricity to the bathroom and removing the existing faceplates from the walls. Measure the wall height and the distance from the tub to the ceiling, as well as the width of the wall. Transfer these measurements to the sheetrock, marking the cuts with a pencil. Using a utility knife and straight edge, score the sheetrock along the marked lines, then snap it along the scored line.

a bathroom that is being remodeled with pink paint
a bathroom that is being remodeled with pink paint
How to finish Drywall around tub or shower surround
How to finish Drywall around tub or shower surround

For the piece against the tub, measure and cut a 2x4 to fit between the wall studs at the level of the tub's lip. This will provide support and protect the sheetrock from future water damage. Attach the 2x4 to the studs with drywall screws.

Attaching the Sheetrock to the Wall

Starting at the top, hold the first sheetrock panel in place, with the bottom edge-aligned with the ceiling. Use drywall screws to attach the panel to the studs, spacing them roughly 12 inches apart. Typically, you'll use screws with plastic washers to prevent the paper from tearing. Ensure the screws are slightly recessed, but do not countersink them.

AD

Be mindful of electrical outlets and plumbing when attaching the sheetrock. Cut out or notch the sheetrock as necessary to fit around these fixtures, using the utility knife and straight edge. When the first panel is securely attached, measure and cut the next panel to fit snugly against the first, following the same process for screw placement and notching as needed.

Finishing the Joints: Taping and Mudding

Once all the sheetrock panels are attached, the next step is to create a seamless, smooth surface. This involves taping the seams and applying joint compound, or 'mud,' to create a solid, uniform surface for painting or wallpapering.

Start by applying drywall tape to the seams, using a wide putty knife to press the tape firmly into the joint compound. Work in small sections, running the tape along the center of the seam, and applying a thin layer of joint compound on both sides of the tape. Allow the compound to dry slightly before pressing the tape into place, ensuring there are no lumps or air bubbles.

AD

Applying the First Coat of Joint Compound

Begin applying the first coat of joint compound, referred to as the 'first mud,' using a 6-inch or 8-inch trowel with a beveled edge. The goal is to completely fill the seam with compound and create a slightly rounded, smooth surface. Work in small sections, applying the compound using the trowel at a 45-degree angle to the seam. Be careful not to apply too much pressure, as this can cause the tape to detach from the wall.

After applying the first mud, allow it to dry completely, following the manufacturer's instructions for drying time. Once dry, use a sanding screen or sandpaper to lightly sand the seams and remove any excess compound. Vacuum the sanding dust from the wall, and wipe the area with a damp cloth to remove any residual particles.

Applying the Second Coat of Joint Compound

The next step is to apply a second coat of joint compound, often referred to as the 'second mud.' This coat helps to create a smooth, uniform surface and hides any imperfections from the first layer. Using a trowel, apply a thin layer of compound to the seams, using long, smooth strokes that travel parallel to the seam. Be sure to feather the edges of the compound, tapering it off to ensure a smooth transition to the surrounding wall surface.

AD

Again, allow the compound to dry completely, and lightly sand the seams using a sanding screen or sandpaper. Wipe the wall with a damp cloth to remove any sanding dust, and check for any missed spots or imperfections. Apply a third and final coat of compound, if necessary, to achieve a perfectly smooth surface.

Finishing Touches: Corner Beads and Touch-ups

The final step in the sheetrocking process is to apply corner beads to the edges of the wall, ensuring a clean, professional finish. Corner beads are designed to protect the drywall from damage and create a smooth, ninety-degree angle at the edge of the wall. They come in various materials, including metal and vinyl, and can be found at your local hardware store.

Measure and cut the corner bead to fit the length of the wall, using a utility knife or tinsnips. Apply joint compound to the edge of the wall, using a trowel to create a thin, even layer. Press the corner bead into the compound, using a straight edge to ensure it's positioned correctly and perpendicular to the wall. Apply a thin layer of compound over the corner bead, using a wide putty knife to press it firmly into place. Allow the compound to dry, then lightly sand the corner bead and wall surface, and wipe clean with a damp cloth.

With the sheetrocking complete, you're now ready to paint or wallpaper your bathroom walls, transforming the space into a stylish, inviting oasis. Don't forget to reinstall the faceplates for the electrical outlets and light switches, ensuring they're properly secured and functional. Embrace the sense of accomplishment that comes with tackling a home improvement project on your own, knowing that you've added value and personal touches to your living space. Happy DIYing!

AD