how to sharpen a ripping chain

Mastering the-edge: Your Ultimate Guide to Sharpening a Ripping Chain

By Richard Wilson
AD

Nothing beats the satisfying hum of a well-maintained chainsaw, but that's only possible with a sharp ripping chain. A dull chain not only hinders your work but also stresses your saw's engine, leading to premature wear and tear. So, let's dive into how to sharpen a ripping chain, ensuring it's always ready for your next project.

Before we begin, remember that chainsaw maintenance is an ongoing process. Regularly checking and sharpening your chain is as crucial as sharpening it for the first time. Your chain manufacturer recommends sharpening every 5 to 10 hours of usage, but this may vary depending on the wood type and the chain's quality.

Understanding Your Ripping Chain

A ripping chain is designed for cross-cutting, reducing the risk of kickback. It consists of cutters and tie straps, with each cutter having a top and bottom plate facing different directions. A sharp chain has four cutting edges per cutter, two per plate.

AD
How to Sharpen a Chainsaw Chain
How to Sharpen a Chainsaw Chain
HOW TO SHARPEN A CHAINSAW CHAIN.
HOW TO SHARPEN A CHAINSAW CHAIN.
How to sharpen chainsaw with a dremel
How to sharpen chainsaw with a dremel

To sharpen your chain correctly, you must grasp the peculiar design of the cutters. The top plate faces forward, and the bottom plate faces backward. The top plate's edges are used for cutting, while the bottom plate's edges are designed to clear wood chips.

Gathering Your Equipment

Before you start, ensure you have all the necessary tools handy. You'll need a chainsaw sharpening tool, a file guide or a chain vise, and a 5/32" round or flat file. If you're using an electric sharpener, you'll also need the correct sharpening stones.

How to Sharpen a Chainsaw (DIY)
How to Sharpen a Chainsaw (DIY)
How To Make A Ripping Chain For A Chainsaw - Hunker
How To Make A Ripping Chain For A Chainsaw - Hunker

Always prioritize safety. Wear proper gloves and goggles. Also, ensure your chainsaw is unplugged or the spark plug is removed if you're using a gasoline-powered one. If you're unsure about any step, consult your chainsaw's manual.

Removing the Chain

First, disconnect the spark plug boot (if using a gas-powered saw) or unplug the saw. Then, use an Allen wrench to loosen the chain adjuster screw, allowing the chain to slide off the sprocket. After that, disengage the chain from the saw's body and remove it completely.

AD

While the chain is off, use this opportunity to clean it. Remove any embedded debris and excess lubricant with a brush and mild soap. Let it dry before sharpening to avoid any slippage.

Sharpening the Ripping Chain

Now that your chain is clean and removed from the saw, it's time to sharpen it. It's essential to maintain the factory-set angle, typically 30° to 35° for ripping chains. Using a file guide or a chain vise helps maintain this angle. If you're using an electric sharpener, follow the instructions provided by the manufacturer.

Start by identifying the cutters. On a ripping chain, you'll see that the top plate faces forward, and the bottom plate faces backward. Remember this orientation as you'll need to sharpen each plate separately.

AD

Sharpening the Top Plate

Place your chain in the chain vise or file guide, ensuring the top plate is facing up. Hold the file securely at the designated angle. Starting from the outer edge, carefully draw the file across the cutter, moving towards the center. Repeat this until you've created a sharp edge.

Important: Never sharpen more than two or three teeth at a time. Over-sharpening can remove too much metal, weakening the cutter. Also, ensure you're maintaining the correct angle throughout the process.

Sharpening the Bottom Plate

After sharpening the top plate, flip your chain over so the bottom plate is facing up. Repeat the process, drawing the file from the outer edge to the center. As previously mentioned, maintain the correct angle and don't sharpen more than two or three teeth at a time.

AD

Once you've sharpened all the cutters, clean the chain again, removing any filings. Lubricate it lightly with a few drops of bar oil and re-install it on your saw. Ensure it's properly tensioned and engaged with the sprocket before storing it or using it.

Ta-da! Your ripping chain is now sharper than ever, ready to take on any cross-cutting challenge. Regular maintenance is key to keeping your chain in top condition. Happy sawing!

AD