how to restring pella blinds

Step-by-Step Guide: How to Restring Pella Blinds

By Nicole Brown
AD

Ever found yourself struggling with the cord of your Pella blinds? Over time, the tension and use cause the cord to fray and eventually break. Instead of investing in a new set, learn how to restring Pella blinds and restore functionality to your window shades. This guide will walk you through the process step-by-step, ensuring your Pella blinds lift and lower perfectly again.

Restringing Pella blinds may seem daunting, but with the right tools and patience, anyone can do it. This guide will arm you with the knowledge needed to tackle this DIY project, saving you time and money in the long run. Let's dive into the process of restringing Pella blinds.

Gather Your Tools

Before you begin, make sure you have all the necessary tools to complete the job. You'll need:

AD
How to Restring Levolor Window Blinds
How to Restring Levolor Window Blinds
someone is holding a small piece of metal in front of a window with white blinds
someone is holding a small piece of metal in front of a window with white blinds
How to Restring Bamboo Roll-up Blinds | windmillprotea.com
How to Restring Bamboo Roll-up Blinds | windmillprotea.com
  • New Pella blind cord (ensure it's the same size as the original)
  • Scissors
  • Tape measure
  • Pliers
  • Screwdriver (if your blinds have tassels, you'll need to remove them first)
  • Ladder (if your blinds are high up)

The key is getting the right replacement cord. Pella blind cords come in various sizes, so measure your current cord to ensure you purchase the correct one.

Remove the Old Cord

Begin by unscrewing the wand or pull cord from the headrail. Set it aside, ensuring not to lose the small screw. If your blinds have tassels, now's the time to remove them by gently pulling them off.

How to Restring a Horizontal Wood Blind
How to Restring a Horizontal Wood Blind
Restring Pella Between-the-Glass Mini Blinds
Restring Pella Between-the-Glass Mini Blinds

Next, cut the tangled or broken cord using scissors or pliers. You'll likely need to snip it in a few places to removed tied portions completely. Once fully removed, discard the old cord and tassels (if applicable).

Measure and Cut the New Cord

Measure the length of the new cord, adding a few extra inches to account for tying knots at the top and bottom. Cut the cord to size.

AD

For most Pella blinds, you'll want two cords - one for lifting and one for lowering. Ensure that both cords are cut to the same length for balanced operation.

The Restringing Process

Now that you've prepared your blinds and cord, it's time to restring them. Follow these steps to ensure a smooth and even distribution of tension.

Feed one end of the cord through the small hole in the operation bracket, located at the bottom of the blind. Pull it up until you can comfortably reach the headrail. Tie a knot in the cord to prevent it from slipping back through the hole.

AD

Attaching the Cord to the Headrail

Thread the new cord through the eyelet on the existing cord railing (also known as the drum). You should now have a loop of cord hanging above the headrail. Wrap the loop around the wand or pull cord base and pull it through the loop, essentially tying it to the headrail.

Adjust the tension by slackening or tightening the knot. Once you've achieved the right balance, trim any excess cord and discard it.

Installing the Lower Limit Tension Hole

Pella blinds feature a lower limit tension hole, which prevents the cord from pulling too high and causing strain on the blinds. Measure and mark 6" from the bottom of the blind, then drill a hole at this point. Insert the small piece of dowel rod or coiled cord through the hole to create a stopping point for the cord.

AD

Wrap the other end of the cord around the dowel rod or coil, then thread it back through the operation bracket. Pull the cord until you hear it click into place at the lower limit. Carefully lower the blind to ensure it functions correctly.

Reinstall the Wand or Pull Cord

Reattach the wand or pull cord to the headrail, ensuring it's properly secured. If your blinds had tassels, Now's the time to reinstall them as well.

Test your newly restringed Pella blinds by lifting and lowering them. Adjust the tension if needed, and you're all set!

Restringing your Pella blinds allows you to maintain your window coverings without replacing them entirely. The process may take time to perfect, but with each பrection, your confidence and skill will grow. Don't hesitate to tackle this DIY project - you've got this! And what's more, whenever you look at your perfectly functioning blinds, you'll enjoy a well-deserved sense of accomplishment.

AD