how to restring a toro weedeater

How to Restring a Toro Weedeater

By Mark Wilson
AD

If your Toro Weedeater isn't trimming like it used to, it might be time to replace the line. Restringing your Weedeater isn't as complicated as it sounds, and with a few simple tools, you can have it trimming in no time. Let's dive into a step-by-step guide on how to restring a Toro Weedeater.

Before we start, make sure to unplug your Weedeater and wear work gloves to protect your hands. Also, ensure you have the following tools and materials ready: a ratchet tie-down strap, a line holder tool (like the Weed Eater String Trimmer Head), and a new string spool that's compatible with your Weedeater model.

Understanding Your Toro Weedeater

Toro Weedeaters come in two common types: straight shaft and curved shaft. The process is slightly different for each, so make sure you're following the right steps for your model. First, let's identify which type you have:

AD
How To Restring Your Toro Flex Force Weed Wacker In Under a Minute!
How To Restring Your Toro Flex Force Weed Wacker In Under a Minute!
How to restring RELOAD STRING on TORO 60V weed trimmer weedeater
How to restring RELOAD STRING on TORO 60V weed trimmer weedeater
HOW TO Re-String A Weedeater Grass Trimmer
HOW TO Re-String A Weedeater Grass Trimmer

Straight Shaft: The shaft is a single piece, with the spool and head at the end of the tool. Most commercial and heavy-duty models have a straight shaft.

Curved Shaft: The shaft consists of two parts connected by a joint. The spool and head are at the end of the longer, curved section. Most residential models have a curved shaft.

a man is working on an electric motor
a man is working on an electric motor
DIY Toro Pull Cord Repair – Easy Step-by-Step Instructions
DIY Toro Pull Cord Repair – Easy Step-by-Step Instructions

Preparing Your Weedeater

Once you've identified your Weedeater type, it's time to prepare it for restringing:

  1. Unplug the Weedeater: Safety first! Unplug the power cord from the outlet.
  2. Remove the guard: Using a screwdriver or wrench, remove the debris shield or guard from the head. The guard protects your legs from flying debris when you're using the Weedeater.

Removing the Old Line

Now that your Weedeater is prepared, it's time to remove the old line:

AD

First, locate the release button or spool lock on your Weedeater. This button stops the spool from spinning while you're feeding in the new line. Press and hold the button, then grasp the top of the line with your pliers and pull it out of the head. Continue pulling the line until it's completely removed from the spool.

Next, remove the remainder of the old line from the spool. You may need to use your pliers to gently tug at the line and unwind it from the spool. Once the old line is completely removed, discard it.

Mounting the New String Spool

With the old line out of the way, it's time to mount the new string spool. Toro uses different spool sizes for their Weedeaters, so make sure you have the correct one for your model. Here's how to mount it:

AD

Feed the Line Through the Head

Start by threading the new line through the hole in the spool's center. Then, insert the line through the eyelet or hole in the Weedeater's head.

If you're using a straight-shaft Weedeater, you can skip the next step. If you're using a curved-shaft model, continue to the next subheading.

Attaching the Line Holder Tool (Curved Shaft Models)

For curved-shaft Weedeaters, you'll need a line holder tool to feed the line through the joint. Insert the tool's hook through the hole in the head, and then secure it to the line with the tool's clip or ratchet.

AD

Gently pull the line, guiding it through the joint and out the other end. Once the line is fed through, remove the line holder tool.

Winding the New Line onto the Spool

Now that the line is fed through the head, it's time to wind it onto the spool. Here are the steps:

  1. Hold the Line: Hold the end of the line with your fingers to keep it taut while you wind.
  2. Wind the Line: Using your other hand, grasp the spool's edge and wind the line around the spool in a clockwise direction. Make sure to wind it evenly and tightly, with no overlap or gaps between the turns.
  3. Stop Winding Early: Wind the line until it's about 6-8 feet left on the spool. This length allows for some trimming before you'll need to replace the line again.

Securing the Line

Once you've wound the line onto the spool, you'll need to secure it to prevent it from unwinding. Here's how:

Fold the remaining line end back onto the spool, creating a small loop. Then, use your ratchet tie-down strap to secure the line to the spool. Wrap the strap around the line and spool repeatedly, using the ratchet to tighten it each time. You may need to use your finger to hold the line in place and prevent it from slipping.

Once the line is secure, trim the excess line from the tie-down strap using your scissors. Be careful not to cut the line itself.

Reassembling and Testing Your Toro Weedeater

Now that the line is wound and secured, it's time to reassemble your Weedeater and test it:

Reinstall the Guard

Reattach the debris shield or guard to the head, using your screwdriver or wrench to secure it in place. Ensure the guard is properly aligned and covers the entire head.

Test the Weedeater

Plug in your Weedeater and start it up. Gently pull the trigger, and the line should feed out smoothly as it trims. Check to ensure the spool is spinning freely and the line is cutting evenly.

If your Weedeater isn't trimming properly, double-check that you've wound the line tightly and securely, and that there are no kinks or twists in the line. If you've followed these steps correctly, your Toro Weedeater should be ready for another season of trimming.

Congratulations! You've successfully restrung your Toro Weedeater. Now that you know how, you can keep your Weedeater in top condition with regular maintenance and restringing. Happy trimming!

AD