how to replace the belt on a maytag dryer

Step-by-Step Guide: How to Replace the Belt on a Maytag Dryer

By James White
AD

If your Maytag dryer isn't performing as efficiently as it used to, it might be time to replace the belt. A worn-out belt can cause your dryer to overheat, make excessive noise, or not heat at all. Fear not, this task is quite manageable with the right guidance. Here's a comprehensive step-by-step guide to help you replace the belt on your Maytag dryer.

Before you start, ensure you have the following tools and parts at hand: a screwdriver (Phillips or flathead, depending on your dryer model), a new dryer belt that fits your Maytag dryer model, and a bit of patience. Always remember to unplug your dryer from the power source and turn off the gas valve if you have a gas dryer before you begin.

Accessing the Dryer Belt

The dryer belt is typically located at the back of the dryer, behind the drum. To access it, you'll need to remove some panels and the rear access panel.

AD
✨ OLDER MAYTAG DRYER BELT REPLACEMENT - EASY DIY FIX ✨
✨ OLDER MAYTAG DRYER BELT REPLACEMENT - EASY DIY FIX ✨
Maytag Dryer Repair – How to replace the Multi-Rib Belt
Maytag Dryer Repair – How to replace the Multi-Rib Belt
How to Replace a Belt on a Maytag Dryer
How to Replace a Belt on a Maytag Dryer

Start by unplugging your dryer and turning off the gas valve if applicable. Then, locate the screws at the back of the dryer, usually in the lower right or left corner. Remove these screws using your screwdriver. After that, pull off the rear access panel. The belt should now be visible.

Removing the Old Belt

Before removing the old belt, note its position around the pulleys to ensure you install the new one correctly. The belt typically goes around the drum in one direction and the motor pulley in the other direction.

DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide
DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide
OLD MAYTAG DRYER BELT REPLACEMENT
OLD MAYTAG DRYER BELT REPLACEMENT

To remove the old belt, you'll need to disengage the idler pulley. This is usually controlled by a tension bracket or spring. You can do this by pulling on the belt at the bottom, which should release some slack. Then, carefully slide the belt off the pulleys and discard it.

Identifying the Idler Pulley

The idler pulley is the one that the belt runs through to create tension. It's usually located lower than the motor pulley and the drum pulley. It might be controlled by a tension bracket or spring, which you'll need to release to remove the old belt and install the new one.

AD

In some models, the idler pulley might be adjusted by a screw. If that's the case, turn the screw counterclockwise to release the tension on the belt before removing it. Once you've identified the idler pulley and understood how it works, you can proceed to remove the old belt.

Removing the Drum

To facilitate the process of removing the old belt and installing the new one, you might need to remove the drum to gain more access space.

First, disconnect the drive shell from the front of the drum. This usually involves removing a few screws. Then, carefully pull the drum out of the dryer. Make sure to support the drum to avoid any injuries or damages. With the drum removed, you should have enough space to work around the belt area.

AD

Installing the New Belt

Before installing the new belt, ensure it's the correct size and type for your Maytag dryer model. You can find this information in your dryer's owner's manual or by contacting a Maytag representative.

Start by routing the new belt around the pulleys, following the path of the old belt. Then, reengage the idler pulley, applying the same amount of tension as the original belt. Ensure the belt is evenly tensioned on both sides to prevent any slippage.

Replacing the Drum

Once the new belt is installed, you can start putting back the dryer together. First, reinsert the drum into the dryer opening and reconnect the drive shell to the front of the drum.

AD

Ensure the drum is properly aligned and secured before proceeding. After that, you can start replacing the rear access panel and the screws you removed earlier. Ensure everything is correctly secured and aligned to avoid any damages or issues in the future.

Testing the New Belt

Before plugging your dryer back in, perform a quick test to ensure the new belt is working correctly. Turn the drum by hand to check the belt's operation. The belt should turn the drum smoothly without any excessive friction or noise.

If the belt seems to be working correctly, you can now plug your dryer back in and turn it on. Allow it to run for a cycle to confirm that the new belt is functioning properly. Always monitor your dryer in the first few uses to ensure everything is working as it should.

And there you have it! Replacing the belt on your Maytag dryer is a straightforward task with the right guidance. Always remember to be patience and double-check every step to ensure the safety and efficiency of your dryer. If you're unsure about any step, don't hesitate to contact a professional or your dryer's manufacturer for further assistance. Happy repairing!

AD