how to replace shoes on hayward navigator

How to Replace Shoes on Hayward Navigator: A Step-by-Step Guide

By Laura Hernandez
AD

Shoe replacement on a Hayward Navigator pool cleaner may seem daunting, but it's a critical maintenance task that ensures optimal performance. Regularly replacing shoes keeps your cleaner's traction and efficiency intact. Let's guide you through this process with a step-by-step, SEO-optimized guide.

Before you begin, gather these materials: new shoes designed for your Navigator model, a screwdriver (most likely Phillips), and a new o-ring (if needed). Ideally, perform this task annually or every 250 hours of operation, depending on usage.

Understanding Your Navigator's Shoes

Hayward Navigator shoes, also known as "traction shoes" or "cams", are engineered to hug the pool floor, ensuring your cleaner moves smoothly and efficiently. They're designed to wear out over time, hence the necessity for replacement.

AD
Flap Kit Wing Kit Pod Shoes Replacement For Hayward Navigator Pool Cleaner
Flap Kit Wing Kit Pod Shoes Replacement For Hayward Navigator Pool Cleaner
How to stop shoes from squeaking
How to stop shoes from squeaking
the toothbrush has been placed next to it's attachments
the toothbrush has been placed next to it's attachments

Your Navigator model might use one of these shoe types: the DiamondCam, RubberCam, or GroovedCam. Each offers unique advantages, but the replacement process remains largely the same.

Identifying Worn-out Shoes

Inspect your current shoes for these signs of wear and tear:

Hayward Axv414p Navigator & Pool Vac Pod Shoe Replacements for Concrete - 4 Pack, Multicolor
Hayward Axv414p Navigator & Pool Vac Pod Shoe Replacements for Concrete - 4 Pack, Multicolor
Hayward Navigator Ultra Pool Vac Pod Shoes Wing Kit Replacement Cleaner Parts
Hayward Navigator Ultra Pool Vac Pod Shoes Wing Kit Replacement Cleaner Parts
  • Excessive smoothing or polishing on the surfaces that touch the pool floor
  • Loose or wiggling shoes, even slightly
  • Exposed or broken shoe mounting hardware

Choosing the Right Replacement Shoes

When selecting new shoes, ensure they match your Navigator's model number. Hayward provides a handy chart on their website to simplify the process. Rapid replacement of worn shoes can minimize potential damage to your cleaner and save on future repairs.

Removing Old Shoes

Start by shutting off and unplugging your Navigator. Lay it on its side, ensuring thediri­ct drive motor doesn't come into contact with the ground.

AD

Using your screwdriver, carefully loosen and remove the screws securing the shoes. Some models may require more than one screw per shoe. Gently pry out the old shoes, taking note of how they fit for correct reassembly.

Inspecting O-Rings

While the shoes are off, inspect the o-ring that seals the shoe's shaft. If it's cracked, twisted, or shows signs of wear, replace it to maintain a proper seal and prevent leaks.

Mounting New Shoes

First, apply a small amount of grease to the shoe's shaft to help it rotate smoothly. Align the new shoe with the drive shaft and push it onto the shaft until it meets the o-ring. Don't force the shoe; a gentle push should suffice.

AD

Wiggle the shoe slightly to ensure it's seated correctly. Then, reinsert the screws and gently tighten them using your screwdriver. Be careful not to overtighten and strip the screws.

Adjusting and Testing Your Navigator

Once the new shoes are installed, turn your Navigator back upright and plug it in. Fill the cleaner with water and set the timer for a test run.

After a few minutes, check the cleaner's progress. It should move smoothly over the pool floor, skimming and vacuuming effectively. If it seems slow or struggling, the shoes may not be properly aligned, or the o-ring could be damaged.

AD

Monitoring Shoe Performance

After running your Navigator with the new shoes, observe their performance over the next few cleaning cycles. Most shoes will improve traction and efficiency during the first few uses as the surfaces break in.

Even with proper maintenance, shoe replacement is inevitable. Regularly inspect your Navigator's shoes and plan for periodic replacements to keep your pool cleaner working at peak performance.

Now that you've mastered the art of replacing shoes on your Hayward Navigator, you're well on your way to keeping your pool spotless with minimal effort. Happy cleaning!

AD