How to Replace a Schlage Door Handle: A Step-by-Step Guide
Are you thinking about replacing your Schlage door handle but unsure where to start? You're not alone. Schwag lockdowns have led many homeowners to tackle home improvement projects they've been putting off. Luckily, replacing a Schlage door handle is a straightforward DIY project that can significantly enhance your home's security and aesthetics. Let's dive into a step-by-step guide to help you replace your Schlage door handle with ease.
Before we begin, ensure you have the following tools and materials on hand: new Schlage door handle set, screwdriver, Phillips drill bit, drill, chisel, hammer, tape measure, pencil, and a steady hand. Always prioritize safety by turning off the power to your doorknob's electrical components if your handle is part of a smart lock or keyless entry system.
Preparation and Removal
Preparation is key to a successful Schlage door handle replacement. Start by measuring your existing doorknob to ensure the new one is compatible. Once you're confident the new handle will fit, gather your tools and let's begin.
Before removing the old doorknob, disconnect any electrical components to prevent damage. For standard doorknobs, twist the thumbturn counterclockwise to unlock the knob. Use a flathead screwdriver to unscrew the faceplate, then remove the old doorknob by turning it counterclockwise.
Old Handle Removal
Begin by removing the old doorknob by unscrewing the setscrew on the latch side of the door. The setscrew is usually covered by a cap or rosok screw, which you'll need to remove using a screwdriver. About half of Schlage door handles have setscrews on both the latch side and the exterior knob, so check both sides before proceeding.
Once you've removed the setscrew, pull the latch out of the door. If it's stuck, gently tap the end of the latch with a hammer to loosen it. If it's still not budging, you may need to use a chisel to widen the latch hole slightly. Be careful not to damage the door or the latch itself.
Prepare the Door
With the old doorknob removed, inspect the door for any damage. If the knob hole or latch hole is worn or damaged, you may need to fill it with wood filler and allow it to dry before proceeding. This will help ensure a snug fit for your new Schlage door handle.
Measure the thickness of your door to ensure your new doorknob is the right size. Standard interior doors are 1⅜" thick, while exterior and metal doors can range from 1⅞" to 2½". Once you've confirmed the thickness, it's time to prepare the door for your new doorknob.
Installing the New Schlage Door Handle
Now that your door is prepared, it's time to install your new Schlage door handle. Begin by inserting the latch provided with your new doorknob through the latch hole in your door. Make sure the edge of the latch is flush with the door edge, and the latch bolt extends far enough into the door jamb to engage the strike plate.
Attach the latch faceplate to the latch using the screws provided. Ensure the faceplate is centered and flush with the door's surface. If your new doorknob has a prepassage feature, install the prepassage plate now, following the manufacturer's instructions.
Install the Interior Doorknob
Insert the interior doorknob spindle through the doorknob hole in the latch side of the door. Align the splines on the spindle with the slots in the latch and the interior doorknob. This will ensure the doorknob turns freely when you install the setscrew.
Secure the interior doorknob to the spindle using the setscrew. Tighten the setscrew by hand as much as possible, then use a screwdriver to tighten it further. Be careful not to overtighten, as this can strip the setscrew or damage the spindle.
Install the Exterior Doorknob
Insert the exterior doorknob and its spindle through the knob hole on the outer side of the door. Align the splines on the spindle with the slots in the exterior doorknob and the latch. Ensure the exterior doorknob is oriented correctly, with the keyhole facing the appropriate direction.
Secure the exterior doorknob to the spindle using the setscrew, following the same procedure as the interior doorknob. Again, be careful not to overtighten the setscrew. Once both doorknobs are secure, try turning them to ensure they function smoothly.
Congratulations! You've successfully replaced your Schlage door handle. By following these steps, you've improved your home's security, aesthetics, and functionality. Don't forget to test your new doorknob to ensure it operates correctly and locks or unlocks as expected. If you encountered any challenges during this project, don't hesitate to contact a professional or Schlage's customer support for assistance. Happy improvement!