how to replace motorcycle clutch cable

Step-by-Step Guide: How to Replace Motorcycle Clutch Cable

By Steven Jackson
AD

Engaging in routine maintenance is vital to keep your motorcycle in optimal condition. One critical component that requires periodic checking is the clutch cable. Over time, it can wear out, leading to reduced performance or even complete failure. If you find yourself in this situation, don't panic. Replacing a motorcycle clutch cable is a task you can handle yourself, saving you time and money. Let's guide you through a comprehensive, step-by-step process on how to replace a motorcycle clutch cable.

Before you start, ensure you have the right tools and materials. You'll need a clutch cable (specific to your motorcycle's make and model), a clutch cable adjustor, a clutch cable disconnect tool, a measuring tape, and some basic mechanic's tools like pliers, screwdrivers, and wrenches. Safety should be your priority, so gear up with gloves, safety glasses, and protective clothing.

Disconnecting the Clutch Lever

To access the clutch cable, you need to disconnect it from the clutch lever. Start by removing the cable's protective boot from the lever. Then, use a clutch cable disconnect tool to push the cable's end out of the lever. If you don't have a specific tool, you can use a flathead screwdriver gently. Once the cable is free, pull it out carefully to avoid damage.

AD
Repairing/Replacing a motorcycle steel cable end(throttle/clutch/brake)
Repairing/Replacing a motorcycle steel cable end(throttle/clutch/brake)
1M views · 6.6K reactions | Put a padlock on the clutch cable and learn the secret A simple emergency trick to replace the cable when it snaps #USA #MechanicHack #EmergencyFix #MotoTricks | Master of Solution
1M views · 6.6K reactions | Put a padlock on the clutch cable and learn the secret A simple emergency trick to replace the cable when it snaps #USA #MechanicHack #EmergencyFix #MotoTricks | Master of Solution
Extended Clutch Cable
Extended Clutch Cable

Similarly, disconnect the cable at the clutch lever's pivot point. You might need to remove a nut or bolt to achieve this. Remember to keep track of any small parts to prevent losing them.

Removing the Old Clutch Cable

With the cable disconnected from both ends, the old cable should now be free. Pull it out gently from the routing through the handlebar and frame. Be cautious not to damage the cable's housing or proximate parts. If the cable is stuck, you might need to gently persuade it with a suitable tool, being careful not to scratch or dent parts around it.

Magura's Hydraulic Motorcycle Clutch
Magura's Hydraulic Motorcycle Clutch
Your Motorcycle Clutch Cable Could Use an Adjustment
Your Motorcycle Clutch Cable Could Use an Adjustment

Once the old cable is out, compare it with the new one to ensure they match. Then, clean the area where the cable was routed to remove any debris or dirt that could harm the new cable.

Installing the New Clutch Cable

The new cable should be similar in length to the old one. However, it's essential to confirm this before installing it. Measure the old cable and compare it with the new one. If they don't match, you might need to adjust the new cable's length, which should be done at the clutch cable adjustor.

AD

With the correct length confirmed, route the new cable through the handlebar and frame, following the old cable's path. Ensure the cable isn't pinched or rubbing against anything. Then, re-install the cable to the clutch lever's pivot point and reconnect it to the lever using a clutch cable disconnect tool or a flathead screwdriver.

Adjusting the New Clutch Cable

After installing the new cable, it needs to be adjusted to maintain proper tension. Start by loosening the adjustment nut on the clutch cable adjustor. Then, using a wrench, turn the adjustor clockwise until there's slight tension on the cable. Be careful not to overtighten, as this can damage the cable or the clutch system.

Once you've reached slight tension, tighten the adjustment nut to lock the setting. Then, test the clutch lever to ensure it functions correctly. If necessary, fine-tune the tension by adjusting the nut as required. Finally, re-install any removed parts and double-check everything is secure and functioning as it should.

AD

Replacing a motorcycle clutch cable can seem daunting at first, but with patience and careful attention to detail, it's a task well within the reach of any competent motorcycle owner. Regular maintenance and addressing issues promptly, like replacing a worn-out clutch cable, go a long way in ensuring your motorcycle's longevity and optimal performance. So, gear up, grab your tools, and get to it – your motorcycle will thank you!

AD