how to replace kenmore water filter

How to Replace a Kenmore Water Filter

By Nicole Robinson
AD

Regular maintenance of your Kenmore water filter is crucial to ensure fresh, clean water in your home. Replacing the filter is a simple task that requires no special tools or expertise. In this guide, we will walk you through the process, step by step, to replace your Kenmore water filter efficiently and effectively.

Before we begin, ensure you have the following on hand: your new Kenmore water filter, a screwdriver (usually a Phillips head), and a clean towel to catch any water spills. Additionally, it's a good idea to have a bowl or container to catch any water that may leak when you remove the old filter.

Preparation and Safety Measures

Before you start, ensure that the water supply to your Kenmore water filter system is turned off. This can typically found under the kitchen sink or near your water heater. Once the water is off, turn on the faucet to release the remaining water pressure in the system.

AD
Kenmore Refrigerator Repair – How to replace the Single Water Filter
Kenmore Refrigerator Repair – How to replace the Single Water Filter
(VIDEO) How Do You Remove a Stuck Refrigerator Water Filter?
(VIDEO) How Do You Remove a Stuck Refrigerator Water Filter?
How To Replace Kenmore Coldspot Model 106 Water Filter? - Miss Vickie
How To Replace Kenmore Coldspot Model 106 Water Filter? - Miss Vickie

Next, place a bowl or container under the filter to catch any drips. This will help minimize mess and make the cleaning process easier.

Locating the Filter Housing

The filter housing is usually found near the water inlet. It is a cylindrical unit with a cap at the top. If your system has multiple filters, you may need to check the user manual to identify the specific filter housing you need to remove.

Replacing Kenmore Elite Refrigerator Water Filter
Replacing Kenmore Elite Refrigerator Water Filter
How to Replace Your Refrigerator Water Filter | Maytag
How to Replace Your Refrigerator Water Filter | Maytag

Once you've located the filter housing, follow the arrows on the housing to determine the direction of turns for removing and reinstalling the cap. Some housings may require a clockwise turn, while others may require a counterclockwise turn.

Removing the Old Filter

Place a towel or a bowl under the filter housing to catch any water drips. Then, using the screwdriver, carefully remove the cap from the filter housing by turning it in the direction indicated by the arrows.

AD

With the cap off, you should see the old filter. Slowly pull the old filter out of the housing. Be careful not to spill any of the used filtration media. Dispose of the old filter according to your local recycling guidelines.

Installing the New Filter

Unwrap the new filter and inspect it for any signs of damage. If the filter is damaged, do not use it and contact Kenmore's customer service for a replacement.

Before installing the new filter, rinse it with clean water to remove any dust or debris that may have accumulated during storage. This will help ensure the filter works effectively from the beginning.

AD

Positioning the New Filter

Position the new filter into the filter housing. Ensure the filtration medium is facing the right direction, as indicated by the arrows on the housing and the filter itself.

Gently push the new filter into the housing until it stops. Do not force the filter, as this could damage the filtration medium and the housing.

Securing the Cap

With the new filter in place, replace the cap on the filter housing. Ensure that the cap is properly seated by aligning the arrows on the cap and the housing. Then, using the screwdriver, turn the cap in the direction indicated by the arrows until it becomes snug.

AD

Do not overtighten the cap. Tightening it too much can cause the filter housing to crack or the filtration medium to brake. The cap should be snug but not so much that it's difficult to turn.

Final Checks and Turning the Water Supply On

Before turning the water supply back on, check for any leaks around the filter housing. If there are no leaks, wipe any remaining water from the area with a clean, dry towel.

Once you've confirmed there are no leaks, turn the water supply back on. Allow the water to run for a few minutes to flush out any air in the system. Check the resulting water for any signs of leaks or contamination.

Congratulations, you've successfully replaced your Kenmore water filter! Regular filter replacements are essential for maintaining the water quality in your home. We recommend replacing your Kenmore water filter every six months or as per the specific recommendations in your user manual. Happy filtering!

AD