how to replace garage door bottom seal

How to Replace Your Garage Door Bottom Seal: A Step-by-Step Guide

By Brian Martin
AD

If your garage door isn't sealing as well as it once did, it might be time to replace the garage door bottom seal. A worn-out or damaged seal can let in drafts, moisture, and even pests. It's an easy DIY project that can save you the cost of a professional service. Let's guide you through the process with our comprehensive, step-by-step guide.

Before we dive in, here's what you'll need: a new garage door bottom seal, a utility knife, gloves, and maybe a screwdriver. It's also a good idea to have someone assist you, as lifting the door can be challenging.

Preparation and Removal of the Old Seal

The first step is to prepare your workspace and remove the old seal. This involves checking the door balance, disconnecting the door from its power source, and carefully disconnecting the safety cables.

AD
Replacing Bottom Garage Door Seal Measuring and Installing Tips
Replacing Bottom Garage Door Seal Measuring and Installing Tips
a man painting the side of a garage door with an advertizer saying how to effectively seal your garage door
a man painting the side of a garage door with an advertizer saying how to effectively seal your garage door
How To Replace The Bottom Seal On Your Garage Door Like A Pro - House Digest
How To Replace The Bottom Seal On Your Garage Door Like A Pro - House Digest

With your garage door fully open, disengage the emergency release. Then, dull one of the garage door rollers by gently tapping it with a hammer. This will make it easier to lower the door without it rolling back up. Now, gently lower the door until it's about halfway open.

Disconnecting the Safety Cables

Open the garage door completely, then secure it in the fully open position. Locate the safety cables - they're usually on either side of the door near the bottom. These cables tension the door when it's open and prevent it from crashing down unexpectedly. Carefully disconnect them from the garage door track.

NEVER Replace Garage Door Bottom Seal Until Watching This! Fast & Easy!
NEVER Replace Garage Door Bottom Seal Until Watching This! Fast & Easy!
How to Seal a Garage Door from the Inside Correctly - AudioMav
How to Seal a Garage Door from the Inside Correctly - AudioMav

Next, use a flathead screwdriver to pop out the locking pin on the carriage that supports the garage door. Lift the carriage carefully and secure it out of the way. Now, you're ready to remove the old seal.

Removing the Old Seal

Inspect the old seal and determine how it's secured. It might be held in place with screws, brad nails, or it might be pressed into a Vuplex door bottom track. If it's secured with screws or nails, use a drill or a hammer to remove them.

AD

If the seal is pressed into a Vuplex door bottom track, use a flathead screwdriver to pry it out. Start at one end and carefully work your way along the full length of the seal. Once you've freed the old seal, discard it and clean the area where the new seal will go.

Installing the New Garage Door Bottom Seal

The first step in installing the new seal is ensuring you have the right type. Garage door bottom seals come in different materials, such as vinyl, rubber, or uPVC. Make sure you get a seal that's compatible with your door and track.

Once you've got the right seal, it's time to install it. Depending on the type of seal you have, the process will vary slightly.

AD

Installing a Vuplex or Non-Vuplex Seal

If you're installing a Vuplex or non-Vuplex seal, start by measuring and cutting the seal to fit the length of your garage door. Most seals come in long rolls, so you'll need to trim it to size. Use a sharp utility knife and cut along the dots or lines marked on the back of the seal.

With the seal cut to size, carefully press it into the Vuplex or door bottom track. Ensure it's secured the entire length of the door. If your seal is secured with screws or nails, use your drill or hammer to secure it in place. If it's pressed into the track, you can use a mallet to tap it gently into place.

Installing a Reinforced Seal

Reinforced seals are a bit more complicated to install. They come with an aluminum piece that needs to be inserted into the door bottom track. Start by trimming the seal to size, just like you would with a Vuplex or non-Vuplex seal.

AD

Once the seal is the right size, carefully insert the aluminum piece into the door bottom track. It should fit snugly. Then, insert the reinforced seal into the aluminum piece. Make sure it's fully inserted and Elaine the entire length of the door. Secure it in place with screws or nails, depending on the type of seal you have.

With the new seal installed, it's time to reattach the safety cables and secure the door. Carefully reconnect the safety cables to the garage door track. Then, lower the door to the halfway point and reinsert the locking pin into the carriage. Finally, reengage the emergency release and test the door.

Replacing your garage door bottom seal is an easy and affordable way to maintain your garage door's functionality and appearance. By following these steps, you can ensure your new seal lasts for years to come. Don't forget, if at any point you feel unsure, it's always best to consult a professional. Stay safe and happy sealing!

AD