how to replace front axle u joints on a dodge ram

Dodge Ram Front Axle U-Joint Replacement: A Step-by-Step Guide

By Richard Jackson
AD

Are you experiencing vibration while driving your Dodge Ram? It could be due to worn-out front axle u-joints. Don't ignore these symptoms; they'll only worsen and increase the risk of expensive repairs. Replacing them yourself is not only cost-effective but also quite doable with the right guidance. Let's dive into how to replace front axle u-joints on your Dodge Ram step by step.

Before starting, ensure you have the necessary tools and parts. You'll need ajack, jack stands, sockets/wrenches, a breaker bar, pliers, and of course, the new u-joints. For this guide, we'll be focusing on the 2003-2012 Dodge Ram 1500, but the process is similar for other models.

Preparation and Removal of the Old U-Joints

First, safely jack up the vehicle and support it securely on jack stands. Remove the tires and lower the axle to gain sufficient clearance.

AD
Dodge Ram 1500 U joint, diagnosis and replacement
Dodge Ram 1500 U joint, diagnosis and replacement
How to change ball joints on a 2002 Dodge Ram 1500
How to change ball joints on a 2002 Dodge Ram 1500
Anti-Sway Bar Drop Brackets for Dodge Ram | Hell Bent Steel
Anti-Sway Bar Drop Brackets for Dodge Ram | Hell Bent Steel

Locate the axle u-joints: there should be one near the differential and another near the transmission. Use a pickle fork or a sledgehammer and a large screwdriver to carefully pry the old u-joints off the spindle and the axle.

Disconnecting the U-Joints

Secure the driveshaft with a piece of wire to prevent it from spinning while you're removing the u-joints. Use(Big) Channel locks or a large grabber tool to squeeze the snap rings off the u-joint.

How to Replace Front Lower Ball Joints 2011-2018 Ram 1500
How to Replace Front Lower Ball Joints 2011-2018 Ram 1500
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram

Slide the u-joint clevis off the shaft. If it's stuck, try to dent it with a hammer on the flat part of the fork, and then pry it off with a screwdriver. Repeat this process for both u-joints.

Removing the Axle Shaft

Unbolt the eccentric shaft supporter and slide it off. Freeing the axle altogether, now it's time to remove the rear u-joint.

AD

Using a breaker bar and the correct socket, loosen and remove the two bolts holding the rear u-joint in place. Tap the rear end of the axle with a sledgehammer until the rear u-joint clears the trans. Now, pull the entire axle out.

Installation of New U-Joints

Start by greasing the new u-joints. This will make the installation much easier and provide better protection for your new u-joints.

Reinstall the axle into the transmission and differential. Tap it in place with a hammer if needed. Ensure the lugs on the u-joints face the right direction: towards the vehicle's rear.

AD

Securing the New U-Joints

Slide the new u-joints onto the axle. Taper the clevis onto the bearing so you can slide the new u-joint onto the shaft. Secure it with the snap ring. Checking with a dial indicator to ensure the angle of the new u-joint matches the trans and the diff.

Reassemble the eccentric shaft supporter and tighten its bolts. Spin the driveshaft a few times to ensure everything is mating together correctly. Torque the u-joint bolts to spec.

Now that you've successfully replaced your front axle u-joints, remember to monitor their condition regularly. Driving habits and terrain can greatly affect their lifespan. Don't forget to take your Dodge Ram in for scheduled maintenance to ensure its longevity and optimal performance. Happy drives, and remember, safety first!

AD
AD