how to replace fender

Step-by-Step: Replace Your Fender Like a Pro

By Melissa Hernandez
AD

Fenders on your vehicle play a crucial role in protecting the vehicle's underside from debris and damage caused by rough roads. Over time, however, these fenders can become damaged, dented, or cracked, requiring replacement to maintain the vehicle's safety and aesthetic appeal. If you find yourself in such a situation, here's a comprehensive guide on how to replace a fender, ensuring a professional outcome while keeping your costs down.

Before proceeding, it's essential to gather the necessary tools and materials. You'll typically need a jack and stands, tire iron or crowfoot, pry bars, flathead screwdriver, drill, drill bits, screwdriver, and new fender bolts. Additionally, you might require a fender pulling tool for a smooth and straightforward process.

Preparation and Removal of the Old Fender

Begin by preparing your work area. Make sure the vehicle is on a flat, stable surface with adequate lighting. Engage the parking brake for safety and chock the wheels to prevent rolling. If necessary, use a jack and stands to lift the vehicle off the ground, providing better access to the fender.

AD
HOW TO REPLACE YOUR RV FENDER SKIRT
HOW TO REPLACE YOUR RV FENDER SKIRT
a man is looking at his cell phone in front of a green mustang muscle car
a man is looking at his cell phone in front of a green mustang muscle car
the engine compartment and its components are shown in this diagram, which shows the location of the
the engine compartment and its components are shown in this diagram, which shows the location of the

Using a tire iron or crowfoot, loosen and remove the wheels nuts, but don't remove the wheel yet. This improves access and helps in changing the fender angle if needed. Now, remove the bolts securing the fender to the vehicle's body. In some cases, you might need to use a drill to break loose rusted bolts.

Removing the Fender

With the bolts removed, use pry bars to carefully prize the fender away from the vehicle's body. You might encounter clips or screws that secure the fender to the inner fender liner or the vehicle's body. Use a flathead screwdriver to remove these, taking note of their positions for reassembly. If required, use a fender pulling tool to slowly and evenly pull the fender away from the vehicle's body.

How to replace a broken car fender turn signal repeater
How to replace a broken car fender turn signal repeater
Easiest way to do fender flares
Easiest way to do fender flares

Once the fender is loose, lift it off the vehicle, watching out for any remaining clips or screws. Wiggle the fender gently to release any remaining tension and free it from the vehicle. Inspect the fender and body lines for any noticeable damage, as this will impact the fender replacement process.

Inspecting and Preparing the Vehicle's Body

Prior to installing the new fender, carefully examine the vehicle's body for any rust, debris, or damage. Clean the area thoroughly, removing any dirt or debris that might interfere with the new fender's fit or adhesion of any sealants. If necessary, use a body filler to repair any minor damage or gaps in the body, ensuring a smooth surface for the new fender.

AD

Before installing the new fender, prepare it for fitting. Clean both the fender and vehicle's body using a suitable cleaner to remove any grease, oil, or debris. This step ensures optimal adhesion of any sealants and provides a clean, secure fit for the new fender.

Installing the New Fender

With the vehicle and new fender prepared, it's time to begin the installation process. Start by positioning the new fender in place, aligning it with the vehicle's body lines and marking any screw or bolt holes that don't align with the existing holes. Marking these locations allows you to drill new holes in the fender, ensuring a proper fit.

Drill new holes as needed, using the same diameter bit as the fender bolts to maintain a proper fit. Install the new fender bolts, leaving them slightly loose to allow for adjustments during the installation process. Secure the fender to the vehicle's body using the new bolts, ensuring an even and flush fit throughout the entire fender.

AD

Securing the Fender

With the fender bolts in place, use a ratchet and socket to snug the bolts, being careful not to overtighten and strip the threads. Once tightened, use a torque wrench to secure the bolts to the recommended factory torque. This ensures a secure and even fit, helping to prevent vibration and wear on the fender and bolts.

Reinstall any clips or screws removed during the old fender's removal, ensuring a secure and proper fit. If necessary, apply a small amount of sealant around the fender's edges, creating a watertight seal to protect the vehicle's underside and interior from moisture and debris.

Final Touches and Testing

Before reinstalling the wheel and lowering the vehicle, take a moment to inspect the fender's fit and alignment. Ensure it's flush with the vehicle's body, with no significant gaps or misalignments. If necessary, adjust the fender bolts or use washers to achieve the desired fit.

AD

Reinstall the wheel, torquing the lug nuts to the appropriate specifications. Lower the vehicle using the jack, ensuring it's stable and level. Take the vehicle for a short drive, testing the fender's fit and performance on both smooth and rough roads. If necessary, make any final adjustments to ensure a secure and safe fit.

Regularly inspect your vehicle's fenders, addressing any damage or misalignment promptly to maintain safety and protect your vehicle's underside. Replacing a fender can be a straightforward task when armed with the correct knowledge and tools. However, if you're unsure about any aspect of the process, consult a professional for guidance and assistance.

AD