how to replace coolant reservoir

How to Replace a Coolant Reservoir: Step-by-Step Guide

By Daniel Garcia
AD

coolant system is an integral part of your vehicle's engine, preventing it from overheating. If you notice a leak, or the reservoir is low, it's time to replace it. Replacing a coolant reservoir isn't rocket science, but it does require careful attention to detail. Here's a step-by-step guide on how to replace your coolant reservoir.

Before you start, gather the necessary tools and materials. You'll need a new reservoir, a socket wrench, penetrating oil, a screwdriver, a funnel, and new coolant. Ensure you're choosing the right coolant for your vehicle, as different vehicles require different types.

Preparation and Draining

The first step is to ensure your engine has cooled down to prevent any burns. Once cooled, locate the reservoir under the hood. It's usually positioned near the radiator and is made of plastic. Check the owner's manual if you're having trouble finding it.

AD
Coolant Reservoir Boiling: Engine Not Overheating?
Coolant Reservoir Boiling: Engine Not Overheating?
HOW TO: Make a coolant reservoir tank
HOW TO: Make a coolant reservoir tank
How to clean, restore, whiten your coolant overflow tank
How to clean, restore, whiten your coolant overflow tank

Before draining, inspect the reservoir for any cracks or leaks. If you find any, you may need to replace it with a new one. Use a socket wrench to loosen and remove the reservoir's mounting bolts. Gently pull the reservoir away from the engine, being careful not to damage any surrounding components.

Draining the Old Coolant

Position a drain pan underneath the vehicle's radiator and loosen the radiator's drain plug using a socket wrench. Allow the coolant to drain completely. You may need to use a screwdriver to help break the seal. Once all the coolant has drained, tighten the drain plug again.

HOW TO CHECK AND ADD COOLANT TO YOUR CAR WITHOUT GETTING BURNED!
HOW TO CHECK AND ADD COOLANT TO YOUR CAR WITHOUT GETTING BURNED!
Why is your car going through coolant so fast?
Why is your car going through coolant so fast?

Now, open the reservoir'soverflow tube using a screwdriver and allow any remaining coolant to drain. The tube is typically located on the side of the reservoir. This will help to prevent any spills when refilling.

Removing the Old Reservoir

Once all the coolant has been drained, it's time to remove the old reservoir. If it's stuck or hard to remove, use some penetrating oil and let it soak for a few minutes. Then, try again. If the reservoir is damaged or leaking, replace it with a new one.

AD

After removing the old reservoir, clean the area around the mounting points to ensure there's no residual coolant. This will make it easier to install the new reservoir and create a better seal.

Installing the New Coolant Reservoir

Inspect the new reservoir for any cracks or defects before installation. If everything looks good, apply a small amount of sealant around the mounting bolts to create a better seal and prevent leaks.

Position the new reservoir over the mounting bolts and carefully push it into place. Ensure it's correctly aligned with the engine's components. Tighten the mounting bolts by hand at first, then use a socket wrench to secure them. Be careful not to overtighten them, as this can cause the reservoir to crack.

AD

Refilling the Coolant

With the new reservoir securely in place, it's time to refill the coolant system. Consult your vehicle's owner's manual for the correct coolant type and quantity. Typically, you'll need a 50/50 mixture of coolant and distilled water.

Using a funnel, pour the new coolant into the reservoir until it reaches the "Full" line. Allow the coolant to settle, then check the radiator's level. If it's below the center, add more coolant through the radiator's cap, also using a funnel. Always ensure the engine and radiator cap are cool before opening.

Final Checks and Driving

With the new coolant added, start the engine and allow it to idle. Monitor the temperature gauge to ensure it's not rising too quickly. If it is, you may have an air pocket in the system. Turn the engine off, let it cool, then prise open the radiator cap to allow any air to escape.

AD

Once the engine is cool, check the coolant levels again and add more if necessary. After ensuring the reservoir and radiator caps are securely closed, take your vehicle for a short drive, then let the engine idle again to allow the coolant to circulate.

That's it! You've successfully replaced your coolant reservoir. Remember, regular maintenance is key to keeping your engine running smoothly. Always consult your vehicle's owner's manual for specific instructions tailored to your make and model. Happy driving!

AD