how to replace belt on samsung dryer

How to Replace Belt on Samsung Dryer: Step-by-Step Guide

By Emily Jones
AD

Is your Samsung dryer not performing as it should? A worn-out or broken belt could be the culprit. Replacing the belt is a manageable DIY task that can save you the cost of a professional repair. Here's a step-by-step guide on how to replace a belt on your Samsung dryer.

Before you begin, ensure you have the following tools and parts: a Phillips screwdriver, a flathead screwdriver, and a new dryer belt compatible with your Samsung dryer model. Always consult your dryer's manual for model-specific advice.

Preparing to Replace the Belt

Safety is paramount when dealing with appliances. Before starting, unplug your dryer from the power source and turn off the gas supply if applicable. Allow the dryer to cool down to prevent burns.

AD
Samsung Dryer Belt Replacement - Not Spinning or Starting
Samsung Dryer Belt Replacement - Not Spinning or Starting
Quick Fix: How to replace the Drive Belt in Your Samsung Dryer (Fixes Not Tumbling) Part 6602-001655
Quick Fix: How to replace the Drive Belt in Your Samsung Dryer (Fixes Not Tumbling) Part 6602-001655
Dryer Runs but Drum Won't Spin? Replace the Belt — Samsung (6602-001655)
Dryer Runs but Drum Won't Spin? Replace the Belt — Samsung (6602-001655)

Next, clear the area around the dryer. You'll need space to move around and lay out your tools and parts. It's also a good idea to have a flat surface nearby to place the removed screws and components.

Accessing the Belt

Begin by removing the dryer's lint filter and the control panel, revealing the dryer drum. You may need to unscrew the panel, depending on your dryer model. Consult your manual for specific instructions.

How to Replace a Dryer Belt on Whirlpool Models
How to Replace a Dryer Belt on Whirlpool Models
How to Replace Dryer Belt on Any Front Load Clothes Dryer
How to Replace Dryer Belt on Any Front Load Clothes Dryer

Locate the screws securing the front panel of the dryer. These are typically found at the bottom. Remove these screws, then carefully pull the panel off, disconnecting the door switch wire harness.

Removing the Old Belt

The belt is usually wrapped around the drive motor pulley at one end and the idler pulley at the other. To remove it, first, find the idler pulley, which is held in place by a rod or a bracket. Remove the rod or bracket using a Phillips or flathead screwdriver, as appropriate for your model.

AD

Next, carefully slide the idler pulley off the belt. Then, using your hands or needle-nose pliers, slide the belt off the drive motor pulley. Once the belt is loose, pull it out from underneath the drum.

Installing the New Belt

With the old belt removed, it's time to install the new one. Start by reinstalling the idler pulley. Align it correctly and secure it using the rod or bracket you previously removed.

Now, take the new belt and loop it around the idler pulley. Then, loop the other end around the drive motor pulley. Ensure the belt is properly seated on both pulleys. It should loop around the drum once, with no twists or kinks.

AD

Tensioning the Belt

The belt should have some tension to ensure the dryer drum rotates smoothly. To tension the belt, find the idler pulley rod or bracket and gently move it towards the drive motor. This will increase the tension on the belt.

You can use a socket wrench to tighten the mounting bolt for additional belt tension. Be careful not to overtighten, as this can damage the belt or cause the dryer to operate incorrectly. The belt should wobble slightly when you push it with your finger.

Reassembling the Dryer

Now that the belt is installed and tensioned, it's time to reassemble your dryer. Begin by reconnecting the door switch wire harness and reattaching the front panel. Secure the panel using the screws you removed earlier.

AD

Next, replace the control panel and reinstall the lint filter. Once everything is in place, plug your dryer back into the power source and turn it on. Check the drum rotation to ensure everything is working correctly.

Congratulations! You've successfully replaced the belt on your Samsung dryer. Regular maintenance, like this, ensures your dryer runs smoothly and prolongs its lifespan. If you have any questions or encounter difficulties, don't hesitate to consult your dryer's manual or contact Samsung's customer support.

AD