how to replace a shallow well pump

Step-by-Step Guide: Replace Your Shallow Well Pump Like a Pro

By David Jones
AD

If your shallow well pump has Spotify'd its last song, it's time to replace it. Changing a well pump might sound daunting, but with the right guide, you're halfway there. Let's dive into the parts, tools, and steps you need to successfully replace your shallow well pump.

Before we start, ensure you're replacing the pump for a valid reason, like age (pumps last about 8-15 years), motor failure, or reduced water output. Safety first, always turn off the power at the main panel, and test wires with a non-contact voltage tester.

Gather Your Tools and Parts

Having the right tools and replacement pump parts will save you time and frustration. Here's what you'll need:

AD
How to Replace a Submersible Well Pump
How to Replace a Submersible Well Pump
How Much Does It Cost to Replace a Well Water Pump
How Much Does It Cost to Replace a Well Water Pump
a man is working on an old carbuncing machine that has been turned upside down
a man is working on an old carbuncing machine that has been turned upside down

  • Replacement shallow well pump (ensure it matches your existing pump's horsepower and flow rate)
  • Pump puller (or a hoist and thick rope)
  • efeito-wrench (for removing the old pump)
  • Adjustable wrench
  • Volometer (for testing the pump)
  • Teflon tape
  • New well seal (if required)
  • Basic safety gear: gloves, glasses, and ear protection

How to Insulate a Well Pump
How to Insulate a Well Pump
How To Install A Shallow Well Jet Pump
How To Install A Shallow Well Jet Pump

Choose the Right Replacement Pump

Select a pump with the same or higher horsepower as your existing pump. The flow rate should also match. Consulting with a local pump professional can help if you're unsure.

Consider energy-efficient pumps if your old one isn't and calculate initial costs against long-term savings.

AD

Safety First: Power and Water Disconnection

Turn off power at the main panel and remove the fuse for the well. Test wires with a non-contact voltage tester to ensure they're safe to handle. Next, drain the water from the system using a hose or a submersible pump.

If your system pressure tank has a bladder, you may need to replace it while the system is open. Check it for bulges or cracks.

Remove the Old Pump

Now that everything's safe and drained, let's remove the old pump. This is the trickiest part, but it's doable with the right tools.

AD

First, disconnect the electrical wires from the pump. Unthread the pipe connection at the bottom of the pump, using a pipe wrench if needed. Stuff a rag into the open pipe to prevent debris from falling into your well.

Using a Pump Puller

Slide the pump puller's prongs into the slots at the top of the pump. Tighten the nut or bolts to secure the puller. Carefully winch the pump up and out of the well, placing it on a sturdy, waterproof surface.

If you're using a hoist and rope, secure the rope around the pump securely, and carefully lift it out. Be prepared for this to be heavy and potentially awkward to handle.

AD

Inspecting the Well

Before lowering the new pump, inspect the well for any damage or deposits. You might need to clean it out or have it professionally inspected if damage is found.

Replace the well seal if necessary. Check your local building codes, as some areas require professionals to install or replace well seals.

Installing the New Pump

With everything clean and clear, it's time to install the new pump:

  1. Ensure the pump's electrical connections match your wiring. Connect the wires, securing them with wire nuts.
  2. Wrap the male pipe thread with Teflon tape to ensure a tight seal. Screw the pump's pipe connection onto the pipe from your well.
  3. Lower the pump into the well using the pump puller or hoist. Ensure it's at the correct depth (usually 10-20 feet below the static water level).

Priming and Testing the Pump

Prime the pump by removing the priming plug (if the pump has one) and filling the pump with water. Reinstall the plug and turn the power back on at the main panel.

Slowly turn on the pump, listening for leaks. Check your pressure tank and plumbing for signs of leaks. Once everything's tight and the system is fully primes and repressurized, your new pump should be up and running.

Congratulations, you've replaced your shallow well pump! Regularly maintain your pump by cleaning filters and replacing seals as needed. Keep an eye on your water quality, and enjoy the peace of mind that comes with knowing your well's in good hands.

AD