how to replace a hot tub jet housing

How to Replace a Hot Tub Jet Housing

By James Thomas
AD

Are your hot tub jets not performing as they once did? It might be time to replace your hot tub jet housing. This guide will walk you through the process in an easy-to-follow manner. Remember, safety is paramount when working with electrical components, so always disconnect the power before you start.

Replacing a hot tub jet housing is a task that can be tackled by a handy homeowner, but it's essential to have the right tools and a solid understanding of the process. This guide assumes a basic level of DIY knowledge and will provide clear, step-by-step instructions.

Understanding Your Hot Tub Jets

Before you dive into the replacement process, it's crucial to understand the components involved. Hot tub jets are powered by a blower motor that forces air through the jets, creating thesoothing massage experience. The jet housing is the part that connects the jet to the plumbing, and it's usually the first component to show signs of wear and tear.

AD
Stop That Drip: DIY Guide to Hot Tub Leak Repair
Stop That Drip: DIY Guide to Hot Tub Leak Repair
How to Remove and Repair/Replace Various Spa Jets ~Sundance, Whirlpool etc
How to Remove and Repair/Replace Various Spa Jets ~Sundance, Whirlpool etc
Spa/Hot Tub Jets How to Remove & Replace w/Type Comparison ~Sundance Altamar Intellijet
Spa/Hot Tub Jets How to Remove & Replace w/Type Comparison ~Sundance Altamar Intellijet

There are different types of jet housings, each designed to create a unique water pattern. Some common types include rotary jets, pulsating jets, and Shiatsu-style jets. Understanding the type of jet housing you have will help you select the correct replacement part.

Gathering Your Tools and Materials

Before you begin, assemble all the necessary tools and materials. You'll need the following:

the words how to repair and replace a hot - tub air blower are shown
the words how to repair and replace a hot - tub air blower are shown
How to Remove a Hot Tub (Guide!)
How to Remove a Hot Tub (Guide!)
  • New jet housing
  • Screwdriver (usually a Phillips head)
  • Pliers
  • simultainer (to measure voltage)
  • Teflon tape
  • New jet gasket (if not included with the new housing)

Preparation: Safety First

Always prioritize safety when working with water and electrical components. Follow these steps to prepare your hot tub for repair:

  1. Turn off the power to your hot tub at the breaker panel. Tape the switch in the "off" position to prevent anyone from accidentally turning it back on.
  2. Allow the tub to cool down completely. Touching hot surfaces can cause severe burns.
  3. Drain the tub using the drain valve, located at the bottom of the tub. Once drained, wipe down the tub to remove any excess moisture.

Removing the Old Jet Housing

With everything prepped, you're now ready to remove the old jet housing. Follow these steps carefully:

AD

Step 1: Locate the Jet Housing

The jet housing is typically held in place by a screw or two. Use your screwdriver to carefully remove these screws. The housing should now be loose but may still be held in place by the plumbing.
Step 2: Disconnect the Plumbing

Use your pliers to carefully disconnect the plumbing from the jet housing. You may need to wiggle the housing slightly to release it. Be cautious not to damage the plumbing.
Step 3: Remove the Old Jet Housing

AD

Once the plumbing is disconnected, you should be able to pull out the old jet housing. If it's stuck, try wiggling it gently. If it's still not budging, you might need to remove a neighboring jet to free it.

Inspecting and Cleaning the Jet Plumbing

Before installing the new jet housing, take a moment to inspect the jet plumbing. Look for any signs of wear, cracks, or leaks. If you find any issues, you'll need to address them before proceeding.
Clean the plumbing and the surrounding area to ensure no debris or old teflon tape is present. This will help create a tight seal with the new jet housing.

Installing the New Jet Housing

Now that your hot tub is prepped and the old jet housing is removed, you're ready to install the new one. Follow these steps:

AD

Step 1: Prepare the New Jet Housing

Ensure the new jet housing is clean and dry. Inspect the gasket (if included) to make sure it's in good condition. If the gasket is damaged, replace it with a new one.
Step 2: Thread on the Teflon Tape

Wrap a few layers of Teflon tape around the threads of the new jet housing. This will help create a watertight seal, preventing leaks.
Step 3: Install the New Jet Housing

Reconnect the plumbing to the new jet housing, ensuring it's properly seated. Then, slide the new jet housing into place and secure it with the screws you removed earlier.
Step 4: Test for Leaks

Before refilling your hot tub, test the new jet housing for leaks. Do this by applying pressure to the jet, looking for any signs of a leak around the housing.
Step 5: Refill Your Hot Tub and Test the New Jet

Once you've confirmed there are no leaks, refill your hot tub and turn the power back on at the breaker panel. Test the new jet to ensure it's working correctly.

Completing the Installation

With the new jet functioning as it should, all that's left is to replace any panels or covers you had to remove to access the jet housing. Ensure everything is properly secured and looking good.
Don't forget to treat the water in your hot tub as per usual, using the appropriate chemicals to maintain the perfect pH balance and prevent any bacterial growth.

There you have it! With a little patience and the right tools, you've successfully replaced your hot tub's jet housing. Regular maintenance of your jets will help keep your hot tub in top shape, ready to provide relaxation and relief whenever you need it.

AD