how to replace a dryer belt on a maytag dryer

How to Replace a Dryer Belt on a Maytag Dryer

By Joseph Jones
AD

Tired of your Maytag dryer taking forever to dry your clothes? A worn-out belt could be the culprit, causing the drum to rotate at a sluggish pace. Don't let this minor issue turn into a major inconvenience. Learn how to replace a dryer belt on your Maytag dryer with this simple, step-by-step guide.

Before you begin, ensure you have all the necessary tools and parts. You'll need a new Maytag dryer belt (part number 307213), a 1/4-inch nut driver, a flathead screwdriver, and a pair of pliers. Once you have everything ready, it's time to dive into the replacement process. Safety first, so unplug your dryer before starting.

Accessing the Belt and Idler Pulley

To reach the belt and idler pulley, you'll need to access the dryer's interior. Follow these steps:

AD
✨ OLDER MAYTAG DRYER BELT REPLACEMENT - EASY DIY FIX ✨
✨ OLDER MAYTAG DRYER BELT REPLACEMENT - EASY DIY FIX ✨
OLD MAYTAG DRYER BELT REPLACEMENT
OLD MAYTAG DRYER BELT REPLACEMENT
How to Replace a Belt on a Maytag Dryer
How to Replace a Belt on a Maytag Dryer

Disconnecting the Door and Light Assembly

Begin by disconnecting the door and light assembly. Remove the two screws at the bottom of the dryer using the 1/4-inch nut driver. Then, lift the assembly out of the dryer. Set it aside, but keep track of where the door switch wire connects to the terminal block on the control panel.

Next, disconnect the wiring harness for the light. Gently rock the harness to disconnect it from the terminal block. Set the harness aside, ensuring the wire doesn't get tangled inside the dryer.

Maytag Dryer Repair – How to replace the Multi-Rib Belt
Maytag Dryer Repair – How to replace the Multi-Rib Belt
🌎 MAYTAG DRYER - BELT REPLACEMENT - DIY - EASY FIX
🌎 MAYTAG DRYER - BELT REPLACEMENT - DIY - EASY FIX

Removing the Front Panel

Locate the two screws at the top of the dryer, one on each side, and remove them using the 1/4-inch nut driver. Do the same for the screws at the bottom of the panel. With all screws removed, lift the front panel up and off the dryer. Set it aside with the door assembly.

You should now see the dryer drum and the belt that connects it to the motor. Before removing the belt, disconnect the idler pulley wire harness from the terminal on the motor. Gently pull it out of itsbracket to allow the wire to hang freely.

AD

Removing the Old Belt and Installing the New One

With the interior exposed, it's time to remove the old belt and install the new one. Here's how:

Removing the Old Belt

First, locate the motor pulley. The old belt should be attached to it. Using pliers, carefully pull one end of the belt off the pulley and slide it off completely. Next, remove the belt from the idler pulley. You may need to loosen the idler pulley mounting screw slightly to permit the belt to slip off.

With both ends of the belt free, carefully remove the belt from the groove on the dryer drum. Pull it towards you and discard it.

AD

Installing the New Belt

Start by holding one end of the new belt against the groove on the dryer drum. Make sure the belt is oriented correctly, with the ribbed side of the belt facing the drum.

Next, route the belt around the idler pulley and push it onto the motor pulley. Ensure the belt is correctly positioned on both pulleys and that the ribbed side of the belt faces outwards.

Once the belt is in position, pull the loose end tight against the idler pulley and slip it into the groove on the dryer drum. Make sure the belt is properly seated in the groove and that there's no slack in the belt between the pulleys and the drum.

AD

Reassembling the Dryer

With the new belt installed, it's time to put the dryer back together.

Reinstalling the Front Panel

First, let's reinstall the front panel. Position the front panel on the dryer and align the bottom edge with the dryer chassis. Insert the bottom screws and tighten them using the 1/4-inch nut driver. Do the same for the top screws.

Reconnect the idler pulley wire harness to the terminal on the motor. Ensure the wire is properly seated in its bracket. Then, reattach the door and light assembly. Remember to hook up the door switch wire to the terminal block on the control panel.

Reconnecting the Power and Testing

With the dryer reassembled, plug it back in and turn it on. Listen for the dryer to start up and run smoothly. If you hear any unusual noises or smell burning, turn off the dryer immediately and contact a professional repair technician.

Replacing a dryer belt on your Maytag dryer doesn't have to be a complex task. With a little patience and these clear, step-by-step instructions, you can save time and money by tackling this repair yourself. Stay vigilant about maintaining your dryer, and it will serve you well for years to come. Happy drying!

AD