how to repair water dispenser not cooling

Fixing Water Dispenser Not Cooling: Simple Steps

By Hannah Robinson
AD

Is your water dispenser suddenly lacking its usual cooling chill? Don't let a warm sip turn into a frustrating issue. Here's a step-by-step guide to help you troubleshoot and fix your water dispenser not cooling problem.

Before you start, ensure you have some basic tools ready, like a screwdriver, a thermometer, and a multipurpose lubricant. Safety first, always unplug the unit before starting any repair work.

Inspect the Coils

The first suspect in a water dispenser not cooling issue is usually the evaporator or cooling coils. If these are dirty or damaged, your dispenser won't chill your water.

AD
Water ​Dispenser Repair | Cleveland, Oh | Distillata
Water ​Dispenser Repair | Cleveland, Oh | Distillata
How To Deep Clean Your Water Dispenser
How To Deep Clean Your Water Dispenser
Primo Water Not Dispensing? Fix It Fast Now
Primo Water Not Dispensing? Fix It Fast Now

To access the coils, you'll need to open up the dispenser. Consult your owner's manual for specific instructions, but usually, a few screws at the back or bottom panel will do it. Once you're in, locate the coils, wipe them down with a damp cloth, and inspect for frost buildup or damage.

Cleaning the Coils

If your coils are just dirty, grab a coil cleaning brush or a soft-bristled toothbrush, and gently clean them. You can use a mixture of warm water and mild detergent for cleaning. Ensure you dry the coils completely afterward to prevent rust.

KitchenAid Refrigerator Water Dispenser Troubleshooting - Ready To DIY
KitchenAid Refrigerator Water Dispenser Troubleshooting - Ready To DIY
a water dispenser is shown with the words fix leaking water dispenser
a water dispenser is shown with the words fix leaking water dispenser

For stubborn dirt, you might need to soak the coils in a solution of equal parts water and white vinegar for about 30 minutes. After soaking, scrub, rinse, and dry thoroughly.

Replacing the Coils

If the coils are damaged or bent, they'll need to be replaced. You can purchase replacement coils online or from an appliance repair store. The installation process is usually a reversal of the removal process, but it can be delicate work.

AD

Before installing, ensure the new coils are compatible with your water dispenser model. If you're unsure, consider consulting a professional technician.

Check the Compressor

The compressor is the heart of your water dispenser's cooling system. If it's not running, your water won't cool. Use a multimeter to test the compressor for continuity. If it's faulty, it'll need to be replaced.

To access the compressor, you might need to remove the back or bottom panel of the dispenser. Always consult your owner's manual for specific steps. Replacing a compressor can be complex, so if you're not comfortable with it, consider calling a professional.

AD

Testing the Compressor

Before replacing, ensure the compressor is indeed faulty. Use a multimeter set to the lowest ohms setting to test the compressor for continuity. A working compressor should show around 1 to 5 ohms of resistance. If it shows higher or infinite resistance, it's likely faulty.

Remember to check other components like the start capacitor and run capacitor before blaming the compressor. They could be the culprit instead.

Replacing the Compressor

If your compressor is faulty, it's time for a replacement. Unplug the dispenser, locate the compressor, and carefully disconnect the electrical wires and refrigerant lines. Keep track of where each wire and line goes.

AD

Install the new compressor by reversing the removal process. Ensure the refrigerant lines are securely connected and evacuated, and the electrical wires are correctly reconnected. Then, refill the system with refrigerant and test the compressor.

Inspect the Freon Level

A low refrigerant level can cause your water dispenser not to cool. Check the level using a manifold gauge set, a specialized tool that measures the pressure in the system. A properly pressurized system will show a high (H) side pressure of around 110-130 psi and a low (L) side pressure of around 35-50 psi at 70°F (21°C).

If the pressure is lower than these values, your system might be leaking refrigerant. If you suspect a leak, you'll need to work with a professional repair technician to fix it, as handling refrigerants requires special licenses and equipment.

Refilling the Refrigerant

If the pressure is low but your system isn't leaking, you can refill the refrigerant yourself. Use a refrigerant can that matches your system (R134a for most water dispensers). First, evacuate the system using a vacuum pump, then connect the refrigerant canister and follow the instructions to refill the system.

Always wear appropriate safety gear, including gloves and eye protection, when handling refrigerant cans. Never overfill the system, as this can cause damage to the compressor.

The next time you reach for a cool drink, you can do so confidently, knowing your water dispenser not cooling issue is a thing of the past. Regular maintenance can prevent these issues from happening again. If you're ever unsure about any repair, don't hesitate to call a professional. Cheers to chill water ahead!

AD