How to Easily Remove Seized Brake Drum
Picture this: you're out for a Sunday drive, and suddenly, your car starts shaking like it's trying to do the hula. You pull over, and it becomes clear - your brake drums are seized. Don’t panic, this can be fixed. In this guide, we'll walk you through the process of removing seized brake drums, step by step.
Before we dive in, a word of caution. Working on your brakes can be dangerous if not done correctly. If you're not comfortable doing this yourself, it's always best to take your car to a professional mechanic. But if you're up for the challenge, let's get started.
Preparation: Gather Tools and Understand Your Brakes
First things first, you'll need the right tools for the job. Here's a list to get you started:
- Jack and jack stands
- Socket wrench set
- Breaker bar (for extra leverage)
- Impact wrench or sledgehammer
- Penetrating oil (like WD-40 or PB Blaster)
- New brake shoes and hardware
Understanding your brake system helps too. Brake drums house the brake shoes, which apply pressure to the brake drum's surface to stop the car. When they stick, they seize, making them stubbornly stuck and difficult to remove.
Now, let's look at how to prepare your car for the job.
Lifting and Securing Your Vehicle
Start by lifting your car using a jack. Insert it under the vehicle frame, not the wheel or axle, and lift until the tire is about six inches off the ground. Secure the car with jack stands for safety.
Next, use a C-clamp to secure the brake drum to the hub. This prevents the drum from turning as you attempt to loosen the lug nuts.
Removing the Lug Nuts and Wheel
Using your socket wrench, remove the lug nuts. You might need to use a breaker bar for stubborn ones. Once the nuts are off, remove the wheel.
With the wheel out, you'll now be able to see the brake drum. Before touching it though, let's get back to our list of tools and use that penetrating oil.
Applying Penetrating Oil to Help Crack the Seize
Using a screwdriver or chisel, make small holes in the brake drum to accommodate the tip of your oil can. Inject oil into these holes, covering the entire backside of the drum where the shoes are.
Give the oil some time to work. This can take anywhere from hours to days, depending on how bad the seize is. Patience is key here. After the oil has done its work, you can proceed to the next step.
Using a Sledgehammer or Impact Wrench to Break the Seize
Position the sledgehammer or impact wrench against the brake drum, using the flat edge of the hammer or the wrench'sMEDIUM socket. Give it a few solid blows, letting the force of the impact loosen the seized drum.
If you're using an impact wrench, set it to a low speed to avoid damaging the brake drum. Keep in mind, this process can be noisy and mess with your neighbors, so it's best done in a controlled, private environment.
Removing the Brake Drum
If the drum still doesn’t budge, you can try using a puller tool designed for brake drums. If you don't have one, a pry bar, a hammer, and some brute force might do the trick. Push the pry bar through the Lug holes and pry until the drum starts to move.
Once it's loose enough, you can usually just pull it off by hand. But be careful, those drums can be heavy and greasy! Don’t hurt yourself or damage the vehicle in your haste.
Inspecting and Replacing the Brake Shoes
With the drum off, you'll see the brake shoes. These shoes should move freely when you push them. If they're sticking, that's likely what caused the seize in the first place. If they're old or damaged, replace them.
Before installing new shoes, make sure to lubricate their springs and pivot points with high-temperature brake grease. This prevents them from stretching and binding, which would lead to another seized brake drum.
Reinstalling the Brake Drum
Before reinstalling the brake drum, clean up any rust or old grease from the inside. Then, apply a thin layer of high-temperature brake grease to the mating surface between the drum and wheel hub.
Reinstall the brake drum by pressing it onto the hub. It might take some force, but keep it even and smooth. Once the drum is in place, tap around the edge with a mallet to seat it properly.
Lastly, lower your car back to the ground, replace the lug nuts and wheel, and you're all set. Driving home, keep an eye on your speed and listen for any unusual noises. The best maintenance on your car is always the maintenance you do yourself, so don't be scared to get under the hood!