how to remove riveted ball joints

How to Remove Riveted Ball Joints: Expert Tips

By Sarah Brown
AD

Renewing old joints on vehicles is an essential part of regular maintenance. Riveted ball joints, used in steering and suspension, can wear out over time, leading to issues like vibration or wandering steering. Removing these joints isn't as complex as it sounds, with the right tools and this step-by-step guide.

Before starting, ensure you have all necessary tools: socket sets, breaker bar, jack, jack stand, penetrating oil (like WD-40 or PB Blaster), pickle fork or ball joint separator tool, torch, hammer, and safety glasses. Always work in a well-ventilated area, and wear suitable protective gear.

Preparation and Accessing Ball Joints

Begin by jacking up the vehicle and securely supporting it with jack stands. Remove the wheel for better access to the joint, then spray penetrating oil into and around the joint's fitting. Let it soak for around 30 minutes to one hour.

AD
Removing ball joints with rivets in 6 minutes!
Removing ball joints with rivets in 6 minutes!
Removing and Replacing Tie Rod Ends and Ball Joints
Removing and Replacing Tie Rod Ends and Ball Joints
Don’t Use A Ball Joint Press Like This!! Lower Ball Joint Removal! #mechanic #automotive #ballJoint
Don’t Use A Ball Joint Press Like This!! Lower Ball Joint Removal! #mechanic #automotive #ballJoint

Loosening and Removing Rivets

Using a breaker bar and the appropriate socket, attempt to loosen the castle nut that secures the joint. If it's too tight, use a torch to heat the nut for a few seconds, then try again. Once loose, remove the nut and the cotter pin (if present).

If the rivets are stuck, you may need to drill them out. Carefully drill a hole through the center of the rivet, then use an extractor tool to pull out the rivet. Be cautious not to damage the joint's threads.

How to Remove a Ball Joint Safely - Harbor Freight Ball Joint Separator Tool Review
How to Remove a Ball Joint Safely - Harbor Freight Ball Joint Separator Tool Review
How to Use a Ball Joint Press Tool to Remove, Replace and Install Ball Joints
How to Use a Ball Joint Press Tool to Remove, Replace and Install Ball Joints

Remove the Ball Joint from Control Arm

Locate the pickle fork or use a ball joint separator tool to separate the joint from the control arm. The tool clasps around the joint's stem, and when you pull the handles apart, it expands to push the joint out of the control arm.

Removing the Ball Joint from the Suspension

Using a hammer and wooden dowel, gently tap the joint out of the steering knuckle or lower control arm. Be careful not to damage the joint or the suspension component. If it's stuck due to rust or damage, consider using a ball joint press tool to extract it carefully.

AD

Once removed, inspect the joint and the corresponding component's cup for any signs of wear or damage. Clean any excess grease or rust from the area before installing the new joint.

Cleaning and Preparing for New Joint

Clean the area around the control arm or steering knuckle with a wire brush or a cleaning solution, removing old grease and any rust. Apply new grease to the new joint's stud and grease the cup where the joint will sit.

Installing the New Ball Joint

Position the new ball joint into the control arm or steering knuckle, ensuring it's fully seated. Reapply the castle nut and tighten it with the torque wrench to the manufacturer's specified torque (usually around 65-75 ft-lbs).

AD

Reassembly and Final Checks

Reattach the wheel and lower the vehicle from the jack stands. Apply penetrating oil to the joint's fitting, then turn the steering wheel from lock to lock several times to ensure the new joint moves freely. Finally, take the vehicle for a test drive to check the steering feel and road manners.

Regular maintenance and proper lubrication of ball joints can extend their lifespan significantly. Keep an eye on their condition during periodic inspections, and address any issues promptly to ensure safe and trouble-free driving.

Congratulations, you've successfully removed and replaced riveted ball joints! Regular practice and understanding the unique features of your vehicle will make this process smoother over time. Always consult your vehicle's repair manual for specific details and follow precautions for working on any vehicle component.

AD
AD