how to remove refrigerator handles

Easy Steps to Remove Refrigerator Handles

By Jessica Anderson
AD

Tired of the old, outdated handles on your refrigerator slowing you down? Whether you're aiming for a seamless, minimalistic look or want to make way for sleek, modern hardware, removing refrigerator handles is a breeze. We've compiled a step-by-step guide to help you tackle this DIY task confidently. Let's dive right in!

Before you start, make sure to gather your tools: a screwdriver (Philips or flathead, depending on your handle screws), a measuring tape, new handles or a handle removal kit, and some sandpaper for smoothing any rough edges. Safety first! Unplug your refrigerator to avoid any electrical hazards. Now, let's get started.

Preparation and Handle Removal

rapports are that old handles can be a bit stubborn. Don't worry, with the right technique, you'll have them off in no time.

AD
How to Replace Your Refrigerator French Door Handles
How to Replace Your Refrigerator French Door Handles
Cleaning Yellowed Refrigerator Handles?
Cleaning Yellowed Refrigerator Handles?
REMOVING and RE-INSTALLING HANDLES on a GE SIDE by SIDE Refrigerator
REMOVING and RE-INSTALLING HANDLES on a GE SIDE by SIDE Refrigerator

The process varies slightly depending on whether you're using a plastic or metal handle, but the general steps are the same. Begin by removing the screws holding the handle in place. Depending on your handle, you might need to use a putty knife or a flathead screwdriver to pry it off gently. If it's stuck, apply some gentle force, but be careful not to scratch the finish.

Removing Plastic Handles

For plastic handles, you might find that the screws are tucked away in small cavities. Use a narrow tool like a narrow-blade screwdriver to gently pry them out. If the handle is still not budging, apply some heat with a hair dryer to soften the adhesive and make removal easier.

How to Remove Samsung Refrigerator Door Handles
How to Remove Samsung Refrigerator Door Handles
How to Remove a Dent from a Stainless Steel Refrigerator: 11 Steps
How to Remove a Dent from a Stainless Steel Refrigerator: 11 Steps

Once the screws are out, pull the handle straight out from the sides. If it's still stuck, use a flathead screwdriver to gently pry it off. You might need to repeat this process for each end of the handle.

Removing Metal Handles

For metal handles, the process is similar, but you'll usually find larger screws. Start by unscrewing them completely. If the handle is still stuck, use a putty knife or a flathead screwdriver to gently pry it off. Apply some gentle force, but be careful not to scratch the paint.

AD

If the handle is still stubborn, try heating thearea around the screws with a hair dryer. This will help loosen any paint or adhesive that might be holding it in place. Once the handle is off, sand any rough edges smooth with some fine-grit sandpaper.

Preparing and Installing New Hardware

Now that you've successfully removed your old handles, it's time to prepare for the new ones. Make sure to measure the center point and height of the old handle attachment points to ensure your new handles match up perfectly.

If you're using a handle removal kit, follow the manufacturer's instructions to create new holes. If you're installing new handles, you'll need to drill new pilot holes. Take your time and double-check your measurements to avoid drilling too many unnecessary holes.

AD

Installing New Handles

Before you start, give the new handles a test-fit to make sure they align correctly. Once you're satisfied with the placement, it's time to install them. Use a small amount of threadlocker on the screws to prevent them from vibrating loose over time.

Tighten the screws securely, but be careful not to overtighten and strip the holes or damage the refrigerator door. Once the screws are secure, give the handles a gentle tug to ensure they're properly attached. And there you have it – a fresh, new look for your refrigerator!

Planning for Handle-less Design

If you're aiming for a handle-less design, you've got a bit more work ahead. You'll need to sand down any screw holes or rough edges, then fill them in with Bondo or another automotive body filler. Once the filler is dry, sand it smooth and paint over it to match the finish of your refrigerator.

AD

For a seamless, professional result, consider using aerosol-matched paint and following the manufacturer's guidelines for touch-ups. This will help ensure your DIY project looks perfect in the end.

Congratulations! You've successfully removed your refrigerator handles and given your kitchen a sleek, modern upgrade. enjoy your new, stylish space. Why not continue the refresh by exploring some other DIY kitchen projects? The possibilities are endless!

AD