how to remove hydraulic from chair

Easy Guide: Banish Hydraulics from Chairs - Simple Steps

By Emily Wilson
AD

Tired of dealing with hydraulic squeaks and leaks in your office chair? It might be time to remove the hydraulic cylinder altogether and replace it with a manual gas lift. Not only will this save you from future maintenance hassles, but it's also a surprisingly simple DIY project. Let's guide you through the process, from gathering tools to reassembling your chair with a new manual lift.

The first step is to identify whether your chair uses a hydraulic cylinder. While many modern chairs do, some older models or budget options may still use manual gas lifts. If you're unsure, refer to your chair's user manual or look for the telltale signs of a hydraulic system - smooth up and down motion, a cylinder-like part under the seat, and possible leaks or squeaks.

Gathering Tools and Materials

Before you start, ensure you have the right tools and materials on hand:

AD
Instructions for Removing the Bottom Bearing Clip from Your Office Chair Shock
Instructions for Removing the Bottom Bearing Clip from Your Office Chair Shock
How To Remove and Replace Office Chair Cylinder
How To Remove and Replace Office Chair Cylinder
How to fix a salon hydraulic pump up chair
How to fix a salon hydraulic pump up chair

  • New manual gas lift (ensure it matches your chair's size and weight capacity)
  • Adjustable wrench
  • Hammer
  • Screwdriver (Philips or flathead, depending on your chair's bolts)
  • Pipe wrench (optional, but helpful for removing the old cylinder)
  • Rags or shop towels for cleaning up any hydraulic fluid
  • New lift cylinder grease (if applicable)

DIY Office Chair Repair: Cylinder Replacement
DIY Office Chair Repair: Cylinder Replacement
How to Put Hydraulic Fluid in a Salon Chair?
How to Put Hydraulic Fluid in a Salon Chair?

Preparing Your Workspace

Clear a large enough workspace, preferably a garage or outdoor area, where you can lie the chair on its back without disturbing it. Protect the floor with a drop cloth or newspaper to catch any leaking hydraulic fluid.

Before you start dismantling, take a few minutes to plan and understand the process. Familiarize yourself with your chair's components and how they interact. It's also a good idea to take a few photos as you disassemble, so you'll have a reference point when reassembling.

AD

Removing the Hydraulic Cylinder

1. **Disconnect the backrest:** Most chairs have a lever or knob that releases the backrest. Use this to tilt the backrest forward until it's flat against the seat. If your chair has a separate locking mechanism, disengage that as well.

2. **Remove the seat:** Turn the chair over so the base is facing up. Locate the bolts that hold the seat to the base. These are usually hidden under protective caps and can be tricky to access. Use an adjustable wrench or a screwdriver to remove them. Once the bolts are out, lift the seat off the base.

3. **Expose the hydraulic cylinder:** With the seat off, you should now see the hydraulic cylinder attached to the center column. The cylinder is typically held in place by a nut thatthreads onto a spindle at the bottom of the column.

AD

Replacing the Hydraulic Cylinder with a Manual Gas Lift

Finally, the moment you've been waiting for - removing that troublesome hydraulic cylinder and replacing it with a more reliable manual gas lift.

1. **Remove the old cylinder:** Use an adjustable wrench or a pipe wrench to carefully turn the nut counter-clockwise and loosen it. Once the nut is off, you may need to use a hammer and a flathead screwdriver to tap the cylinder out of the column. If your chair has a locking mechanism on the cylinder, make sure to disengage that first.

2. **Prepare the new manual gas lift:** Ensure the new lift is compatible with your chair's size and weight capacity. If it's greased at the factory, you can skip this step. If not, apply a small amount of lift cylinder grease to the stud before installing it.

AD

Reinstalling the Chair Components

Now that you've successfully replaced the hydraulic cylinder, it's time to reassemble your chair:

1. **_align the new manual gas lift with the column:** Ensure the locking mechanism (if any) on the new lift is engaged, and the lift is in the correct orientation. Align the stud on the lift with the hole in the column, then insert the lift into the column.

2. **Reattach the seat:** Position the seat over the lift and align the mounting holes. Insert the bolts, then use a screwdriver and adjustable wrench to secure the seat to the base.

3. **Reattach the backrest:** Carefully lift the backrest, ensuring it's properly aligned with the seat. Lock it into place using the lever or knob you disengaged earlier.

Congratulations! You've successfully removed the hydraulic cylinder from your chair and upgraded to a manual gas lift. Enjoy your squeak-free, maintenance-light office chair. Remember, regular care - like inspecting the lift mechanism and tightening bolts as needed - will help keep your chair in top shape. Happy working!

AD