how to remove black and decker string trimmer head

How to Remove Black and Decker String Trimmer Head

By Thomas Williams
AD

Whether you're a DIY enthusiast or a professional groundskeeper, knowing how to remove and replace parts of your Black and Decker string trimmer is crucial for optimal performance. One of the most common components to replace is the trifluroethylene (PTFE) or nylon trimmer head, which houses the line spool. Here's a step-by-step guide on how to remove the Black and Decker string trimmer head.

Before you commence, ensure that your string trimmer is unplugged if it's electric, or the engine is cooled if it's gas-powered. Always prioritize safety to prevent injuries. Now, let's dive into the process.

Understanding Your Black and Decker String Trimmer Head

Black and Decker string trimmers come with two primary head types: single-line and dual-line. Most newer models use the bump-feed feature, which allows you to advance the line when you bump the head on the ground. The following steps apply to both head types.

AD
Black & Decker Electric String Trimmer Spool Line Replace Rewind
Black & Decker Electric String Trimmer Spool Line Replace Rewind
Changing a Single Line Spool on a BLACK+DECKER String Trimmer
Changing a Single Line Spool on a BLACK+DECKER String Trimmer
Refill your own Black & Decker AFS String Trimmer Spool and save!
Refill your own Black & Decker AFS String Trimmer Spool and save!

First, gather your tools. You'll need a Phillips or flathead screwdriver, depending on your trimmer model, and a nut driver or wrench for the trimmer head. Also, prepare new trimming line for replacement.

Preparing the Trimmer: Disassembly

Begin by removing the protective cover, usually by unscrewing it or sliding it off, depending on your trimmer model. This will reveal the spool knob and the trimmer head. If your trimmer has a bump-feed head, you'll see a button or lever that allows the line to advance.

How to Change the String on a Dewalt 20v String Trimmer
How to Change the String on a Dewalt 20v String Trimmer

Using the appropriate screwdriver, remove the screw at the center of the trimmer head. If your trimmer has a locking mechanism, you might need to hold the spool in place using the nut driver or wrench while unscrewing. Once the screw is loose, the trimmer head should come off easily.

Inspecting the Trimmer Head

Now that the head is off, inspect the trimmer line for signs of wear or damage. If the line is frayed, broken, or doesn't advance smoothly, it's time for a replacement. Also, check the head for any cracks, especially around the line exit points.

AD

If you're replacing a dual-line head, ensure that the line is spooling correctly on the inside. Some trimmers use athalon (X-shaped) spool, while others use a cိမole (round) spool. Regardless of the spool type, both lines should be wound in the same direction, usually clockwise.

Replacing the Trimmer Line and Head

When replacing the line, it's essential to use the correct type recommended in your trimmer's manual. Most Black and Decker trimmers use standard 0.065" or 0.080" diameter line. Before you start, cut a sufficient length, usually about 20 to 25 feet, for a single-line head and 50 to 60 feet for a dual-line head.

For single-line heads, insert one end of the line through the hole in the spool. If your head has a button or lever, align it with the arrow on the spool. Run the line through the appropriate slot in the head housing, then out through the line exit hole. Leave about 6 to 8 inches of line extending past the housing.

AD

Winding the Line

Wind the line tightly and evenly around the spool, following the direction of the arrow. For single-line heads, leave about 6 to 8 inches of line hanging out of the line exit hole. For dual-line heads, insert the other end of the line through the other hole on the spool, and wind again, leaving about 6 to 8 inches of line on each side.

After winding, ensure that the line is not twisted and that it lies flat against the spool. For dual-line heads, pull both ends of the line taught to ensure they unwind evenly. Trim the ends of the line if they're too long, leaving about 6 to 8 inches extending from the head.

Reassembling the Trimmer Head

Reassemble the trimmer head by reversing the earlier steps. Align the arrow or button on the head with the arrow on the spool, then push the head back onto the trimmer. Replace and tighten the center screw using the appropriate screwdriver. If your trimmer has a locking mechanism, hold the spool in place while screwing.

AD

Finally, replace the protective cover and you're ready to go. Always test your trimmer in a safe, open space before using it on your lawn or garden.

Regular maintenance is key to extending the lifespan of your Black and Decker string trimmer. Always store your trimmer properly, and replace the line before it becomes too short or damaged. With a little care and attention, your trimmer will serve you well for years to come.

AD