how to remove a maytag agitator

How to Remove a Maytag Agitator: Step-by-Step Guide

By Brian Davis
AD

Is your Maytag washer causing grief with a faulty agitator? Don't let the dread of a hefty repair bill or complex instructions deter you. With this step-by-step guide, we've equipped you to tackle "How to Remove a Maytag Agitator" like a pro. Let's dive in and demystify this task.

Before we embark, ensure you have the right tools at your disposal. Safety glasses, a screwdriver, and a putty knife are your essential companions for this task. Now, let's get your washer fixed and ready to spin clean clothes once again!

Preparation and Disassembly

To begin, unplug your washer from the power source and turn off both the hot and cold water supply taps. Drain any remaining water to ensure safe and stable working conditions.

AD
How to remove agitator from Maytag washer mvwc565fw1?
How to remove agitator from Maytag washer mvwc565fw1?
Removing Maytag washer Agitator
Removing Maytag washer Agitator
Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator
Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator

Now, let's break down the initial phase of disassembly:

Accessing the Agitator

Remove the screws securing the top control panel to the washer. Carefully pull out the panel and set it aside. Next, look beneath the panel - remove any screws retaining the wire harness and gently lift it away from the washer body.

Removing a washing machine wash plate the easy way. DIY that anyone can do. Maytag Bravos Agitator
Removing a washing machine wash plate the easy way. DIY that anyone can do. Maytag Bravos Agitator
Maytag Bravos MCT Washer, Stuck Agitator removal
Maytag Bravos MCT Washer, Stuck Agitator removal

With the panel and harness clear, it's time to access the agitator. Remove the two screws holding the plastic cover above the agitator, then slide the cover up and away from the agitator. You'll now see the agitator's center post, which is secured by a nut and a lock washer.

Removing the Agitator Nut and Washer

Using an adjustable wrench, loosen and remove the nut securing the agitator. Be cautious not to overtighten as you turn it in the counterclockwise direction to unscrew it. After removing the nut, slide off the lock washer as well.

AD

With these initial steps completed, you're well on your way to removing the agitator. But don't rush; we're only just getting started! In the next section, we'll tackle the agitator itself.

Removing the Agitator

Now that we've exposed the agitator and loosened its fasteners, it's time to tackle its removal. This is where your putty knife comes in handy. Let's not waste any more time and dive into the process:

Adjusting the Putty Knife

Slide your putty knife between the agitator and the tub. Angle the knife gently to ease the agitator's hub out of the tub's recess. Be patient; you might need to rock the agitator slightly as you pull the putty knife towards you.

AD

If the agitator still refuses to budge, don't force it. Instead, check that you've completely unscrewed the nut and removed the lock washer. Also, ensure that you've angled the putty knife correctly and are applying steady, gentle pressure.

Pulling Out the Agitator

Once you've worked the putty knife around the edge of the hub, lift the agitator directly upward. In some cases, it might still be stubborn. If this happens, try rotating the agitator back and forth as you lift it.

Congratulations! With a little patience and effort, you've finally removed the agitator. Before you celebrate, there's one more crucial step to ensure everything goes back together smoothly: inspect the removals.

AD

Inspection and Reassembly

Before you proceed with reassembly, carefully examine the washer components you've removed. Check for any wear or damage that might have contributed to your agitator issue. Replace any faulty parts to prevent similar problems in the future.

Now, let's reverse the disassembly process to reassemble your washer:

Reattaching the Agitator

Position the new or repaired agitator onto the post by lowering it down and ensuring the hub fits snugly over the post. Replace the lock washer and nut, then tighten the nut using your adjustable wrench. Don't overtighten; just ensure it's securely fastened.

Replace the plastic cover over the agitator and secure it with the screws. Reattach the wire harness and control panel, ensuring they're correctly positioned and securely fastened with screws.

Final Touches

Turn the water supply taps back on and ensure they're correctly connected to the hot and cold water hoses. Plug your washer back into the power source, and you're ready for a test run!

Before you spin your first load, double-check that everything is correctly assembled and functioning. Flipping your washer switch should power the machine and start the spin cycle. If all is well, pat yourself on the back - you've successfully mastered "How to Remove a Maytag Agitator"! Now, keep your washer in tip-top shape with regular maintenance, and you'll avoid agitator trouble in the future.

AD