how to remove a can light

"How to Remove a Can Light

By Christopher Lewis
AD

Ever found yourself in a dim-lit room, wishing you could brighten up your space with the flick of a light switch? Can lights, also known as recessed lights, are a great way to achieve this. But what if you've done your research, measured carefully, and still ended up with a can light that's too bright, too high, or just not quite right? Today, we're going to guide you through how to remove a can light, step by step, for a safer, more illuminating DIY project.

Before we dive into the process, remember that safety always comes first. Unplug the power, turn off the circuit breaker, and ensure the light is completely disconnected before you start. With that out of the way, let's get started.

Understanding Can Lights: Before You Begin

Can lights, especially the new Energy Star-rated models, are more efficient and produce less heat than older models. However, they still generate enough heat to cause damage if not installed or removed correctly. Understanding your light's make and model, as well as the type of housing (housings can be IC-rated for insulation contact or non-IC) can help you determine the best course of action.

AD
How to Remove a Can Light Without Attic Access
How to Remove a Can Light Without Attic Access
two stickers that say get rid of your caned lights on the ceiling above a bed
two stickers that say get rid of your caned lights on the ceiling above a bed
How To Replace An Outdated Can Ceiling Light Without Rewiring - Fortune House Shop
How To Replace An Outdated Can Ceiling Light Without Rewiring - Fortune House Shop

For this guide, we'll assume you're working with a standard, non-IC, incandescent can light installed in a standard ceiling joist.

Gather Your Tools and Materials

Before you start, ensure you have everything you need. The right tools make all the difference in a safe, stress-free DIY job.

You'll need:

  • Safety glasses
  • Screwdriver (Philips or flathead, depending on your light)
  • Utility knife
  • Drywall saw or jigsaw
  • Pry bar or putty knife
  • New drywall for replacement (if needed)
  • Joint compound and drywall tape (if needed)
  • Sanding sponge or drywall sander (if needed)
  • New can light or cover (for replacement)

Disconnect the Power Safely

Safety first! Before you touch anything, ensure the power is off. Turn off the light switch and check that the light fixture is no longer live using a circuit tester.

AD

Once you're certain the power is off, turn off the circuit breaker for the light and, if you're unsure about the circuit, test again before proceeding.

Removing the Can Light: Step by Step

With everything ready, it's time to get your hands dirty. Remember, patience and accuracy are key to a successful removal process.

Let's remove that can light, step by step.

AD

Remove the Light Bulb and Trims

Starting at the top, remove the light bulb, if present. Then, grasp the trim ring firmly and twist counterclockwise to unscrew it from theBody of the can light.

Once the trim ring is off, you should see the back of the can light. Some models may have springs that hold the trim in place; if so, you can fold these back gently to remove the trim.

Disconnect the Wires

Carefully disconnect the wires from the mounting bracket. The black wire is hot (live), and the white wire is neutral. Twist the wires clockwise to loosen them, then pull gently to remove them from the mounting bracket.

AD

Stuff a rag or some towels into the opening to prevent anything from falling into your ceiling cavity if you're planning to replace the light later.

If You're Keeping the Hole but Removing the Light

If you're planning to replace the light with a new one, you can skip to the "Replacing Your Can Light" section. However, if you're removing the light but want to keep the hole, here's how to prepare the space.

Using a putty knife or pry bar, carefully pry up the obblongated baffle that sits inside the can light. This will reveal the square mounting bracket.

Remove the Mounting Bracket

Using a screwdriver, unscrew the mounting bracket from the ceiling joist. You may need to use a drywall saw or jigsaw to cut away any drywall that's preventing the bracket from coming free.

Once the mounting bracket is removed, you should have a clean hole where you can install a cover or prepare for a new light.

Preparing for Replacement: Repairing the Drywall

If you've removed the can light entirely, including the mounting bracket, you'll need to repair the drywall before installing a new light or cover.

Cut a piece of drywall to fit the hole, apply drywall joint compound around the edges, and place the piece in the hole. Let it dry, then apply a thin layer of joint compound over the seam, let it dry, and sand smooth.

Sanding and Priming

Use a sanding sponge or drywall sander to sand the area smooth. Be sure to wear a mask to protect yourself from drywall dust. Wipe away any dust with a damp cloth, then apply a coat of drywall primer to the area.

Let the primer dry completely before proceeding.

Replacing Your Can Light

If you're ready to install a new can light, follow these steps. If you're simply covering the hole with a decorative ceiling medallion or other cover, skip to "Covering the Hole".

Ensure the area is clean and free of debris. If necessary, use a vacuum or brush to remove any dust or dirt from the ceiling cavity.

Installing the Mounting Bracket

Position the new mounting bracket in the ceiling joist. Use a tape measure and level to ensure it's centered and square, then mark the location of the screw holes.

Using a drill or driver, attach the mounting bracket to the ceiling joist using the screws provided with your new can light. Ensure the bracket is securely fastened, as this is what will hold the weight of your new light.

Installing the New Can Light

Thread the electrical wires through the hole in the mounting bracket, then slide the can lightbody into place. Secure the light to the bracket using the provided screws, ensuring the light is level and firmly attached to the bracket.

Stuff some insulation into the opening around the light to prevent convection loops (warm air rising and cooling air falling) and to encourage even lighting from the new can light.

Finishing Up

Replace the trim ring, then install a new light bulb. Turn the power back on at the circuit breaker, then test your new light.

If everything works as expected, you've successfully removed and replaced your can light!

Covering the Hole

If you've decided to cover the hole instead of replacing the light, there are several options available. From antique-look ceiling medallions to simple paintable covers, the choice is yours.

Position the cover over the hole and mark the outline. Use a drywall saw, jigsaw, or utility knife to cut out the excess drywall, then sandwich the cover between the ceiling and the drywall. Secure it in place using the screws or method provided with your cover.

There you have it - removing a can light, with all the steps, tools, and safety measures accounted for. Now that you've successfully tackled this DIY project, why not try something even more challenging? The world of DIY is your oyster!

AD