how to put bearings on skateboard wheels

Mastering Skateboard Wheel Bearings: A Step-by-Step Guide

By Laura Thomas
AD

Ever wondered how to make your skateboard smooth and trouble-free? The secret lies in the humble bearing. Properly installing bearings on your skateboard wheels can significantly improve your riding experience, making it faster, smoother, and more enjoyable. In this guide, we're going to walk you through the process of putting bearings on skateboard wheels step by step, ensuring a professional finish every time.

Before we dive into the nitty-gritty, let's ensure you have the right tools and materials. You'll need a set of skateboard bearings, obviously. But also make sure you have a skate tool, which is a multipurpose tool used to remove and tighten bolts on your skateboard. A hammer, some spare skateboard hardware, and some excel or axle nuts will be handy too. Now, let's get started.

Preparing Your Skateboard

Before you fit your new bearings, you'll need to remove the old ones (if there are any). Using your skate tool, loosen and remove the kingpin, which is the large bolt that holds the truck together. Then, remove the axle nut and washers.

AD
How to make Bearing Faster for skateboard
How to make Bearing Faster for skateboard
Make Your Skateboard Bearings Last FOREVER!
Make Your Skateboard Bearings Last FOREVER!
How I Clean My Bearings
How I Clean My Bearings

Next, prise the wheel off the axle using your skate tool as a lever. If the wheel is stubborn, you might need to gently tap it with a hammer. Be careful not to damage the hub or the axle. Once the wheel is off, remove the old bearing and take note of its orientation.

Understanding Bearings

Skateboard bearings consist of several parts: the inner races, the outer races, and the balls in between. The most common skateboard bearing is the 608, sized at 8mm x 22mm x 7mm. They're typically stamped with an ABEC rating, which indicates their precision and quality.

How to Get Bearings Out of Skate Wheels Without Tool
How to Get Bearings Out of Skate Wheels Without Tool
someone is holding an electric toothbrush with the words, how to use it?
someone is holding an electric toothbrush with the words, how to use it?

Knowing the anatomy of a bearing helps you understand how to install it correctly. The inner race should face inwards, towards the center of the wheel. The outer race should face outwards. This orientation allows the bearings to spin freely and smoothly when you roll.

Preparing the Bearing

Before you install the bearing, clean it thoroughly to remove any debris or dirt. Use a rag and some rubbing alcohol to wipe the bearing, making sure to clean all the intricate parts.

AD

Next, check the bearing's orientation. The inner races should be clean and smooth, without any burrs or rough edges. If the bearing's they're not perfectly smooth, you can use a Shaw Tools Deburring Tool to smooth them out.

Installing the Bearing

Now that your bearing is clean and ready, it's time to install it. Start by sliding the bearing onto the axle of your truck. Ensure the inner race is facing inwards, and the outer race is facing outwards.

Once the bearing is in place, pop the wheel back onto the axle. The bearing should nest neatly into the center of the wheel. Secure the wheel in place using the axle nut. Tighten it firmly with your skate tool, but be careful not to over-tighten. Over-tightening can damage the bearing and make your skateboard hard to roll.

AD

Spacers and Shielded Bearings

Some bearings come with shields or rubbers on one or both sides. These are designed to keep dust and debris out of the bearing, ensuring smooth and efficient rolling. When installing shielded bearings, make sure the shield faces outwards to protect the bearing from dust and dirt.

Spacers are another type of skateboard hardware that can be used with bearings. They're usually placed on one side of the bearing, between the bearing and the truck. Spacers can help center the wheel on the axle and also provide some clearance between the truck and the wheel, preventing them from touching and making unwanted noises. When installing spacers, place them on the side facing the truck.

Reassembling the Truck

With the bearing installed and secure, you can now reassemble your truck. Start by replacing the washer, then thread the kingpin back through the truck and the baseplate. Tighten it firmly, but not too tight. You want your truck to move freely, but not wobble.

AD

Finally, grab your skateboard and take it for a spin. You should feel an immediate difference in the way your board rolls. The turning should feel smoother, and rolling should be faster and more efficient. If your board feels resistance or the trucks are too tight, you may need to tweak the setup a bit more.

And there you have it! You've successfully put bearings on your skateboard wheels like a pro. Regular maintenance of your bearings, including cleaning and lubrication, will ensure your skateboard's smooth performance for years to come. So grab your board and get out there! The world's waiting.

AD