how to purge baseboard heating system

"How to Purge Baseboard Heating System: Step-by-Step Guide"

By John Brown
AD

Over time, baseboard heating systems can accumulate impurities, air pockets, and rust, leading to inefficiency and noisy operation. Purging your baseboard heating system not only improves its performance but also extends its lifespan. In this comprehensive guide, we'll walk you through the step-by-step process of purging your baseboard heating system like a professional.

Before we dive in, it's crucial to understand that baseboard heating systems, also known as hydronic or water heater systems, rely on hot water to heat your home. By purging the system, we'll remove any trapped air, ensuring smooth circulation and optimal heat transfer.

Preparing Your Baseboard Heating System for Purging

Before you start, ensure your system is cool and that the power is off to prevent any risk of injury or damage. Here's what you'll need:

AD
How to Clean Baseboard Heaters
How to Clean Baseboard Heaters
How to Clean Baseboard Heaters
How to Clean Baseboard Heaters
How to Clean Baseboard Heaters (Radiators & Covers) the Right Way
How to Clean Baseboard Heaters (Radiators & Covers) the Right Way
  • A flathead screwdriver or an air bleeding key
  • Plumber's tape or a spare hose clamp
  • A towel or a small bucket to catch any water
  • A vacuum pump or a faucet water bleeder (optional, for larger systems)

Locating the Bleeder Valves

Bleeder valves are usually found at the highest points of the baseboard heating system, often near the ceiling or high on the walls. They may be covered by a decorative cap, so you might need to remove this first with a flathead screwdriver.

Once you've located the valves, use your screwdriver or air bleeding key to open them slightly. This will allow trapped air to escape. If you have a large system or vacuum pump, connect it to the bleeder valve to hasten the purging process.

Say Goodbye to Your Old Baseboard Heater
Say Goodbye to Your Old Baseboard Heater
Heating & Cooling Archives
Heating & Cooling Archives

Monitoring and Controlling the Air-Water Mix

As you open the bleeder valves, you'll see a mix of air and water exit. This is normal. To control this, wrap some plumber's tape or use a spare hose clamp around the valve's outlet to catch the water and prevent it from making a mess. Also, keep in mind that the water may be hot, so take appropriate safety measures.

Close the valve when water starts flowing without air. If you're using a vacuum pump, ensure it's properly fitted and that the air bleeding is proceeding smoothly. If the process slows down or stops, turn off the pump and restart it to create a better suction.

AD

Purging the Baseboard Heating System

Once you've released all the air from the high points, it's time to purge the system from the lowest points to ensure all trapped air is removed. Here's how:

1. Close the previously opened bleeder valves and turn on the power to your heating system. This will create pressure in the system.

2. Start at the lowest point in the system and open the bleeder valves one at a time. Air and water will again escape. Repeat the process of controlling the air-water mix as described earlier.

AD

Dealing with Air-Pockets in the Baseboard Heaters

Sometimes, air can get trapped in the baseboard heaters themselves, forming pockets. To remove these, turn off the power and pressure in the system, then open the bleeder valves at the base of each heater. Use a shopsvac or wet-dry vacuum to suck out the air and water mixture.

Once you've removed the air pockets, close the valves, turn on the power and pressure, and repeat the purging process until the system is completely clear of air.

Testing the System

After purging, close all the bleeder valves, turn on the heating system, and monitor it for a few hours. If you hear no air noises and the system heats up evenly, then the purging was successful. If not, repeat the process until the system is air-free and functioning optimally.

AD

Regularly maintaining your baseboard heating system, including annual purging, not only ensures its peak performance, but also extends its lifespan, saving you money in the long run. Always remember to turn off the power and let the system cool before performing any maintenance tasks. Happy purging!

AD