how to program ram key fob

Unlock Secrets: How to Program Your RAM Key Fob

By Joseph Davis
AD

Programing a RAM key fob might seem like a daunting task, but it's actually a straightforward process that can save you the cost of a visit to the dealership. RAM key fobs use a unique identification code to communicate with your vehicle, and programming a new one involves teaching your car to recognize this new code. Let's dive into the process, step by step.

Before we begin, ensure you have the following: your RAM key fob, the original key fob that came with your vehicle, and the owner's manual for your specific RAM model. The process may vary slightly depending on your vehicle's make and model, so it's always a good idea to consult your manual for the most accurate instructions.

Preparing Your Vehicle and Key Fobs

The first step in programming your RAM key fob is to prepare your vehicle and the key fobs. Start by inserting the original key fob into the ignition cylinder and turning it to the "ON" position without starting the engine. This puts your vehicle in accessory mode, which is required for programming the new key fob.

AD
RAM Key Fob Tricks
RAM Key Fob Tricks
How to Program A Car Key Fob at Home
How to Program A Car Key Fob at Home
Programming a new key fob at home (NO DEALERSHIP!) All Jeep, Dodge and Chrysler vehicles.
Programming a new key fob at home (NO DEALERSHIP!) All Jeep, Dodge and Chrysler vehicles.

Next, locate the "Valet" or "User" button on your RAM's center console. This button is usually labeled andIts function is to erase all stored key fob codes and initiate the programming process. Press and hold this button for about 10-15 seconds, or until the turn signals flash three times. This indicates that your vehicle is in "electronic key programming" mode and ready to learn the new key fob code.

Programming the New Key Fob

Now that your vehicle is in programming mode, it's time to teach it to recognize your new RAM key fob. Begin by inserting the new key fob into the ignition cylinder, but do not turn it. Next, remove the new key fob from the ignition and press the "Lock" button on the new fob twice within five seconds. The turn signals on your vehicle should flash once to confirm that the key fob code has been programmed successfully.

DIY Key Fob Programming – What Works & What Doesn’t
DIY Key Fob Programming – What Works & What Doesn’t
How to Upgrade/Program that Ancient GM Truck Key Fob YOURSELF!
How to Upgrade/Program that Ancient GM Truck Key Fob YOURSELF!

If the turn signals do not flash after pressing the "Lock" button twice, double-check that you performed each step correctly and try again. If you continue to have trouble, consult your owner's manual or contact a professional for assistance.

Verifying the New Key Fob

After programming the new key fob, it's essential to verify that it works correctly. To do this, remove the original key fob from the ignition and try using the new fob to lock and unlock your vehicle. The locks should operate smoothly and consistently with the new fob. If there are any issues, you may need to reprogram the fob or consult a professional for assistance.

AD

Additionally, test the remote start function (if equipped) using the new key fob to ensure that it works properly. Start by pressing and holding the "Lock" button on the new fob for five seconds. The turn signals should flash to indicate that the vehicle is in remote start mode. After a few seconds, the engine should start. Once the engine has started, you can press the "Unlock" button on the new fob to turn the vehicle off.

Programming Additional Key Fobs

If you need to program more than one key fob for your RAM, the process is similar to programming the first one. Start by making sure your vehicle is in accessory mode, as described in the previous section. Then, press the "Valet" or "User" button on the center console to erase all stored key fob codes and initiate the programming process.

With your vehicle in programming mode, follow the same steps to program the additional key fobs as you did with the first one. Be sure to test each new fob to ensure that it works properly before moving on to the next one.

AD

Ejecting and Opening the Trunk with the Key Fob

In addition to locking and unlocking the doors, your RAM key fob can also be used to eject the key from the ignition and open the trunk. To eject the key, press and hold the "Unlock" button on the key fob for five seconds while the key is in the ignition. The key should automatically eject from the ignition.

To open the trunk using the key fob, press and hold the "Trunk" button for five seconds. The trunk should open automatically. If the trunk does not open, consult your owner's manual or contact a professional for assistance.

Programming a RAM key fob is a simple process that can save you time and money. By following the steps outlined above, you can add new key fobs to your vehicle and ensure that they work properly. If you encounter any issues or have questions, don't hesitate to consult the owner's manual or contact a professional for assistance. Happy programming!

AD
AD