How to Pour Concrete Next to Existing Slab
Pouring concrete next to an existing slab can be a daunting task, but with the right techniques and a bit of careful planning, you can create a durable, long-lasting bond between the new and old surfaces.
Before you start, ensure you have all the necessary tools and materials: concrete mix, wheelbarrow, shovel, trowel, concrete expansion joint tool, level, tape measure, rubber gloves, safety glasses, and ear protection for operating power tools. Additionally, prepare the existing slab by cleaning it thoroughly and ensuring it's structurally sound.
Preparing the Site and Existing Slab
The area surrounding the existing slab should be clear and well-prepared to ensure a smooth pouring process and a strong foundation for the new concrete.
Begin by marking the area where you'll pour the new concrete. This will serve as a guide during the process and help you maintain a consistent distance from the existing slab. Use stakes and string to create straight, accurate lines.
Cleaning the Existing Slab
Remove any dirt, debris, or loose material from the existing slab's surface using a broom, brush, or power washer. A clean surface will improve the adhesion between the old and new concrete.
Pay special attention to any niños, cracks, or uneven surfaces on the existing slab. These areas may require additional preparation, such as filling cracks with concrete patch or smoothing uneven surfaces with a paramilitary or concrete grinder.
Priming the Existing Slab
Primer creates a chemical bond between the old and new concrete, enhancing adhesion and preventing the new concrete from peeling off. Apply a concrete bonding primer to the clean, existing slab surface using a paintbrush or roller, following the manufacturer's instructions.
Allow the primer to dry completely before proceeding with the next steps. This typically takes anywhere from 30 minutes to a few hours, depending on the brand and weather conditions.
Preparing the Concrete Mix
To ensure a strong bond between the new and old concrete, mix a small batch of concrete specifically for the area adjacent to the existing slab. This separate mix allows for better control over the pour and achieves a stronger bond.
Follow the manufacturer's instructions for mixing concrete, ensuring you maintain a consistent water-to-cement ratio. For the best results, mix only the amount of concrete you can pour within 30 minutes to prevent the cement from setting too soon.
Adding a Bord on the Existing Slab
Before pouring the concrete, create a 1-2 inch wide by 1/2 inch deep bord or channel along the edge of the existing slab. This bord helps to key the new concrete into the old surface, creating mechanical interlocking and improving the bond's strength.
Use a masonry chisel and hammer or a concrete saw to create the bord. Be sure to wear appropriate safety gear, including gloves, safety glasses, and ear protection when operating power tools. After creating the bord, clean out any loose debris and ensure the edges are smooth.
Setting Up Expansion Joints
To prevent cracking, control where cracking occurs, and maintain spatial separation between the new and old concrete, create expansion joints. Use a concrete expansion joint tool or a piece of scrap wood to create a 1/2 inch wide by 1/4 inch deep groove every 10-15 feet along the outside edge of the new concrete and every 3 feet within the poured area.
These expansion joints are essential for allowing the concrete to expand and contract with temperature changes and preventing uncontrolled cracking. Additionally, applying concrete expansion joint sealer after the concrete has cured will enhance the joint's flexibility and longevity.
Pouring and Finishing the Concrete
With everything prepared, you're ready to pour the concrete adjacent to the existing slab. Begin at one corner of the area and work your way along the slab's edge, placing the concrete mix within the bord and spreading it out using a shovel or trowel.
Once the area along the existing slab is filled, carefully level the concrete surface using a straight edge or screed, ensuring a uniform depth and smoothness. Use a magnesium float to screed off the excess concrete and create a smooth, level surface. Be sure to work the float in both directions to remove any low spots or imperfections.
Finishing and Curing the Concrete
After the concrete has been poured and leveled, use a bullfloat to work the surface and remove any residual laitance or excess water. This will help create a dense, stable surface that is resistant to moisture andRecent damage and wear.
Next, apply and segregate the finish broom to create a textured, non-slip surface and close the concrete's pores, making it more resistant to moisture and wear. Lastly, keep the newly poured concrete moist for at least the first 72 hours to ensure proper curing and the development of maximum strength. This can be achieved through regularly misting the surface or covering it with a layer of wet burlap or plastic sheeting.
Congratulations! You've successfully poured concrete next to an existing slab. By following these steps and exercising patience during the curing process, you'll create a durable, long-lasting bond that will serve you well for years to come.