how to move an electrical outlet horizontal

How to Move an Electrical Outlet Horizontally

By Robert White
AD

Moving an electrical outlet to another location on your wall can seem like a daunting task, but with the right knowledge and tools, it can be accomplished safely and efficiently. This guide will walk you through the process of moving an electrical outlet horizontally, ensuring your new outlet is not only functional but also up to code and safe for your home.

Before proceeding, ensure you have turned off the circuit breaker connected to the outlet and always use caution when working with electrical components. First, let's discuss why you might need to move an outlet horizontally and the tools you'll need to get the job done.

Reasons to Move an Electrical Outlet Horizontally

There could be several reasons why you want to move an electrical outlet horizontally. Perhaps you're rearranging furniture, or maybe you're looking to create a more functional space by aligning outlets with counters or cabinets. Whatever the case, ensuring your outlet is level and centered in its new location is crucial.

AD
How to Move and Install an Electrical Wall Outlet
How to Move and Install an Electrical Wall Outlet
How to Move an Outlet for Beginners | Step by Step with Tips and Tricks
How to Move an Outlet for Beginners | Step by Step with Tips and Tricks
HOW TO MOVE AN ELECTRICAL OUTLET UP THE WALL | Add an Outlet | Install Outlet for Wall Mounted TV
HOW TO MOVE AN ELECTRICAL OUTLET UP THE WALL | Add an Outlet | Install Outlet for Wall Mounted TV

Before you begin, make sure to check local building codes and regulations. While this guide is meant to provide a general overview, specific requirements may vary depending on your location.

Tools Needed

To move an electrical outlet horizontally, you'll need a few essential tools. Here's a list to help you gather everything you need before starting:

an empty room with the words how to add an outlet in 50 seconds on it
an empty room with the words how to add an outlet in 50 seconds on it
How to Move an Outlet Up a Wall (8 Steps)
How to Move an Outlet Up a Wall (8 Steps)
  • A multiplier screwdriver (usually No. 2 Phillips)
  • Wire stripper
  • Needle-nose pliers
  • Fish tape
  • Rubber gloves
  • Old work outlet box (if not already using one)
  • Faceplate (to cover the new outlet)

Preparation and Safety

Always prioritize safety when working with electrical components. Before starting, turn off the power at the circuit breaker and use a non-contact voltage tester to ensure the outlet is not receiving electricity. Once you're certain the outlet is safe to work with, proceed with the following steps:

Removing the Existing Outlet

Begin by removing the faceplate from the existing outlet. If it's tight, you can lightly tap the corners using a hammer and a screwdriver for leverage. Once the faceplate is removed, unscrew the mounting screws and pull the outlet out of the electrical box. Be careful not to damage the wires.

AD

Next, identify the black (hot), white (neutral), and green or bare (ground) wires. Using a wire stripper, strip about 3/4 to 1 inch of insulation from each wire. If the wires are not long enough, you may need to disconnect them from the outlet and run new wiring between the old and new locations. This is a more involved process and may require professional help.

Preparing the New Location

Measure and mark the new location for your outlet, ensuring it's level and centered. If you're using a single outlet box, make sure it's properly spaced and centered in theStud. If you're using a duplex box, ensure you're following proper spacing requirements for each outlet.

Before securing the box, ensure the wires from the old outlet can reach the new location. If necessary, use a fish tape to guide the wires into the new location. Once you're confident the wires will reach, secure the outlet box using screws, ensuring it's level and not too tight against the stud. Keep in mind that the box must be flush with the finished surface, or slightly offset if you're installing it in a wall.

AD

Connecting the Wires

Lay the wires into the new outlet box and connect them to the new outlet. Remember, the black (hot) wire connects to the brass terminal, the white (neutral) wire connects to the silver terminal, and the green or bare (ground) wire connects to the green terminal. Gently tug on each connection to ensure they're secure.

Once the wires are connected, install the new outlet, ensuring it's secured tightly to the box. Then, install the faceplate. Before turning the power back on, use a non-contact voltage tester to ensure there's no electricity flowing to the outlet. If it's safe, restore power at the circuit breaker and test the outlet by plugging in a small appliance.

Troubleshooting Potential Issues

If the outlet isn't working as expected, double-check your connections to ensure they're tight and correct. If you're still having trouble, consider reaching out to a professional electrician. It's always better to be safe and seek help if needed.

AD

Moving an electrical outlet horizontally can be a simple DIY project, but it's crucial to prioritize safety and ensure the job is done correctly. With the right tools, preparation, and attention to detail, you can transform your space into a more functional and efficient environment.

Remember, electrical work may vary depending on your specific situation. Before proceeding with any work, consult local codes and, if in doubt, contact a licensed electrician. Happy upgrading!

AD