how to measure ls pushrod length

"Mastering LS Pushrod Measurement"

By Richard Brown
AD

Measuring pushrod length is a crucial step in diagnosing and maintaining a vehicle's engine, particularly in classic cars or hot rods utilizing pushrod engines like the small-block and big-block Chevy, Ford Windsor, and Mopar V8s. Accuracy in this process ensures optimal engine performance and longevity.

In essence, the pushrod's purpose is to transfer motion from the camshaft to the valve lifters, and its length determines the clearance volume, which influences an engine's compression ratio and power output. To measure pushrod length, you'll need a suitable straight edge or ruler, a marker or scribe, a feeler gauge set for valve clearance measurement, and optionally, a micrometer for precision.

Understanding and Preparing Your Engine

Before you begin, make sure your engine is at a convenient working temperature, ideally not too hot. Many mechanics prefer to measure pushrod lengths after an engine has been running for about 10-15 minutes to allow components to expand to their normal operating dimensions.

AD
How To Measure Pushrod Length
How To Measure Pushrod Length
a woman is measuring her waist with a tape
a woman is measuring her waist with a tape
SLEEVE FORMULA
SLEEVE FORMULA

For accurate measurements, ensure your engine's valve train is tightly assembled and free of leaks. Even a tiny amount of oil from a worn valve seal can significantly impact the measurement by migrating into the lifter valley and affecting the pushrod's positioning.

Measuring Valve Clearance

First, establish the proper valve clearance using a feeler gauge set. This involves setting the engine to Top Dead Center (TDC) for the specific cylinder, measuring the gap between the rocker arm and the lifter body with the valve fully closed, and adjusting the rocker arm's anatomy to achieve the manufacturer's recommended clearance.

LS Logic: 10 Basic Tips to Building Your First LS Engine
LS Logic: 10 Basic Tips to Building Your First LS Engine
Why An Alternator And 16-Volt System Are Beneficial For Drag Racers
Why An Alternator And 16-Volt System Are Beneficial For Drag Racers

Valve clearance measurement is essential because it directly impacts the force applied to the pushrod, affecting both engine performance and longevity. Too little clearance may result in valve 'float' and reduced performance, while too much can cause excessive wear and detonation.

Determining the Desired Pushrod Length

To measure the pushrod length accurately, you must first determine the correct length based on your engine's specifications and performance goals. Consult engine rebuilding guides, speak with fellow enthusiasts, or consult online forums dedicated to your specific engine to establish the ideal pushrod length for your application.

AD

Some engine builders recommend starting with a standard pushrod length and adjusting it by adding or subtracting washers between the pushrod and rocker arm or lifter until optimal performance is achieved. However, this method can be an iterative process that requires substantial time and resources, so careful planning is recommended.

Measuring Pushrod Length: The Step-by-Step Process

Once you have your desired pushrod length and the necessary tools, it's time to measure your engine's current pushrods. Please note that it's usually more practical and cost-effective to replace all your pushrods at once, even if only individual measurements indicate a need for change.

Start by removing the valve covers and exposing the rocker arms and pushrods. You'll need to temporarily secure the pushrods in place during the measurement process to obtain accurate readings. Tape, wire, or a small piece of cardboard can be used to create adjustable supports that hold the pushrods upright against the rocker arms.

AD

Obtaining an Accurate Measurement

With the engine at operating temperature and the valve train assembled, use a straight edge or ruler to measure from the end of the pushrod that contacts the lifter to the point where the other end meets the rocker arm. Make sure to account for any washers or spacers currently in use and include them in your measurement.

Be cautious not to 'trap' excessive oil in the lifter valley during the measurement process. Wipe away any excess oil and ensure a clean, dry surface for an accurate reading.

Cross-referencing and ObtainingNew Pushrods

Once you've measured your existing pushrods, cross-reference your findings against the desired pushrod length you determined earlier. If necessary, order replacement pushrods to match your desired length and specifications.

AD

Reputable engine parts suppliers often provide detailed installations guides, including recommended pushrod lengths for specific engine builds and intended applications. Consult these resources to ensure you're selecting the most appropriate pushrods for your needs.

In the end, measuring and sourcing the correct pushrod length is a vital process that directly impacts your engine's performance and longevity. By taking the time to accurately measure your existing pushrods, determine the ideal length, and source high-quality replacement components, you'll be well on your way to optimizing your engine's power and reliability. The next steps involve installing your new pushrods, ensuring proper clearances, and breaking in your engine to achieve maximum performance.

AD