how to make a swivel base

How to Create a Swivel Base: Step-by-Step Guide

By Jessica Wilson
AD

Creating a swivel base for your furniture, such as a desk or a table, can greatly enhance its usability and aesthetics. This helpful guide will walk you through the process of constructing a swivel base using readily available materials and tools. By the end, you'll have a functional and stylish swivel base that adds a touch of elegance to your space.

Before we dive into the steps, ensure you have the necessary tools and materials. You'll need a circular saw, a jigsaw, a drill, clamps, a tape measure, a pencil, sandpaper, and a safety mask. As for materials, you'll require 2x4 lumber, 1x4 lumber, 2.5-inch and 1.5-inch pocket hole screws, wood glue, staples, and a 1/4-inch plywood circle (for the top surface).

Designing and Cutting the Base

First, determine the size of your swivel base based on the furniture you want to attach it to. For this guide, let's assume we're creating a base that's 18 inches in diameter and 3 inches high.

AD
DIY-HOW TO BUILD A SWIVEL BASE
DIY-HOW TO BUILD A SWIVEL BASE
a metal object is being worked on with screws and nuts attached to the machine
a metal object is being worked on with screws and nuts attached to the machine
Convert upholstered chair to swivel
Convert upholstered chair to swivel

Using a tape measure and pencil, mark out the pieces on your 2x4 lumber. You'll need four 3-inch pieces for the legs, four 18-inch pieces for the base frame, and four 3-inch pieces for the corner supports.

Cutting the Legs and Base Frame

Set your circular saw to make 45-degree angle cuts at each end of the 3-inch pieces to create the legs. Using a jigsaw, cut the 18-inch pieces on both ends at a 45-degree angle to form the base frame.

Turning a Chair into a Swivel Rocker
Turning a Chair into a Swivel Rocker
DIY Swivel Desk Hack: Bougie on a Budget!
DIY Swivel Desk Hack: Bougie on a Budget!

For precise cuts, clamp the wood pieces firmly in place and use a scrap piece to align your saw blade to ensure accurate angles. Always wear a safety mask when using power tools to protect your face and lungs from debris.

Assembling the Base Frame

Apply wood glue along the edges of the 18-inch pieces and connect them, forming a square frame with 45-degree mitered corners. Use bar clamps to hold the joints together tightly while the glue dries, ensuring a strong bond.

AD

Once the glue has set, reinforce the joints by plugging the holes with wooden dowels or using a Kreg Jig to create pocket holes, then secure them with 2.5-inch pocket hole screws. Sand the edges smooth to prepare for the next step.

Attaching the Corner Supports and Legs

Measure and mark the centerpoints of the base frame's inner edges. These will be the attachment points for the corner supports. Use a drill to create pilot holes, then attach the 3-inch corner supports using 1.5-inch pocket hole screws.

Next, attach the legs to the corner supports. Apply wood glue to the contact points, use a drill to create pilot holes, and secure the legs in place with 2.5-inch pocket hole screws. Ensure the top of the legs are flush with the bottom of the base frame for stability.

AD

Building the swivel mechanism

To create the swivel mechanism, you'll need a 1/4-inch plywood circle slightly smaller than the inner diameter of your base frame (in our case, 16 inches). You can trace a large bowl or use a compass to draw the circle, then cut it out with a jigsaw.

Attach a 3-inch translucent plastic cap, usually used for electrical boxes, to the center of the plywood circle. This cap will act as the pivot point for your swivel base. Drill a 1/4-inch hole through the cap and the plywood circle, then insert a 1/4-inch bolt with a washer and nut to create the swivel mechanism.

Attaching the swivel mechanism and top surface

Place the swivel mechanism inside the base frame, ensuring the bolt lines up with the center of the frame. Attach the plywood circle to the base frame using wood glue and 1.5-inch pocket hole screws through the legs and corner supports.

AD

Next, attach the 1/4-inch plywood top surface to the swivel mechanism using a washer and nut. Ensure the top surface is level and spins freely on the mechanism. You can apply a small amount of silicone lubricant to the bolt for smoother rotation if needed.

Finally, consider upholstering the top surface with fabric or adding a decorative edge to enhance the aesthetics of your swivel base. To ensure the longevity of your creation, apply a coat of paint or varnish to protect the wood from scratches and moisture.

Now that you've successfully built your swivel base, attach it to your desired furniture piece and enjoy the enhanced functionality and style it brings to your space. Happy crafting, and remember to always prioritize safety when working with power tools.

AD