how to make a pulse extender

How to Make a Pulse Extender

By Ashley Davis
AD

Creating a pulse extender, also known as a pulse widthSabcdcensor, can significantly boost the range of your pulses in electronic circuits. This versatile device allows you to widen or narrow the duration of electrical pulses, making it crucial in various applications such as shifting signals, delaying or advancing clocks, and creating complex timing sequences. Here's a comprehensive guide on how to make a pulse extender, tailored to both beginners and experienced hobbyists.

The primary goal of this article is to provide a step-by-step guide to building a simple and effective pulse extender. By following this guide, you'll enhance your understanding of digital electronics and gain hands-on experience with essential components and techniques.

Understanding Pulse Width Modulation (PWM)

Before diving into the pulse extender circuit, let's briefly discuss Pulse Width Modulation (PWM). PWM is a popular method for controlling the power supplied to electric loads like motors and LEDs. In PWM, the average power delivered to a load is controlled by turning the switch on and off at a fast rate (typically in the range of kilohertz). The duty cycle, or the ratio of 'ON' to 'OFF' time, determines the fraction of time that the load is powered.

AD
How to Make a Paracord Flower Pattern #shorts
How to Make a Paracord Flower Pattern #shorts
55 Disney Projects & Ideas
55 Disney Projects & Ideas
Electronic fabric lets you play Tetris with your arm
Electronic fabric lets you play Tetris with your arm

Familiarizing yourself with PWM principles will help you understand the pulse stretcher's operation and its potential applications. For instance, by extending the pulse width, you can control the power delivered to the load more accurately or trigger events with a delay.

Components Required for the Pulse Extender Circuit

To build a simple pulse stretcher circuit, you'll need the following components:

  • One 555 Timer IC
  • One 74HC595 Shift Register IC
  • One 10kΩ Resistor
  • One 22kΩ Resistor
  • One 1N4007 Diode
  • One LED (for optional indicators)
  • Breadboarding circuit and jumper wires

The 555 Timer IC generates the timing signals, while the 74HC595 Shift Register IC extends the pulse width. The resistors set up the timing, and the diode protects the circuit from voltage spikes and damages. The LED provides visual feedback for operation verification.

Preparation and Breadboarding

Before beginning, ensure that you have a well-lit workspace and proper tools like a soldering iron, wire strippers, and a multimeter. Arrange the components and breadboard in a neat and accessible manner to avoid confusion during assembly.

AD

Carefully follow the circuit diagram below and map out the components onto your breadboard. Make sure that the power and ground connections are well-placed to prevent accidental short circuits. After the initial setup, double-check your work and ensure that all the components and connections are correctly placed.

Connecting the Components

Start by connecting the 555 Timer IC to the breadboard. Insert it into the center of the board, straddling the middle gap. The notches on either side of the IC should face upwards, designating the top of the IC as pin 16.

Next, connect the components following the circuit diagram. Ensure accurate pin-to-pin connections and double-check for any solder bridges or missing connections. Once you've affirmed the connections, you can proceed to power up the circuit.

AD

Calibrating and Testing the Pulse Extender

Now that your pulse stretcher is assembled, it's time to test and calibrate the circuit. You'll need a power source (like a 9V battery), a minearbe cable, and an oscilloscope or a logic analyzer with a visualization software like Logic Analysis Tool on Saleae.

Connect the power source, and observe the input and output signals using the oscilloscope or logic analyzer. Adjust the 22kΩ and 10kΩ resistors to fine-tune the pulse width. The 22kΩ resistor controls the pulse narrowing, while the 10kΩ resistor determines the pulse widthening.

Pulse Widthening

To extend the pulse width, apply a low logical level (0V) to pin 12 of the 74HC595 Shift Register IC. The extended pulse width will depend on the 10kΩ resistor's value and the trigger's pulse width.

AD

You can verify the pulse widthening by observing the output signal on your oscilloscope or logic analyzer. As you vary the input pulse width and resistance value, note the resulting output signals and adjust your calculations accordingly.

Pulse Narrowing

To narrow the pulse width, apply a high logical level (5V) to pin 12 of the 74HC595 Shift Register IC. The narrowed pulse width will depend on the 22kΩ resistor's value and the trigger's pulse width.

Observe and fine-tune the output pulse width using your oscilloscope or logic analyzer. By experimenting with different resistor values and input pulse widths, you'll gain insights into the pulse stretcher's operation and performance limits.

The power of the pulse stretcher lies in its versatile applications, from controlling loads to creating complex timing sequences. With practice and experimentation, you'll become adept at designing custom pulse stretcher circuits and integrating them into your projects. So go ahead, unleash your creativity, and experiment with your new pulse extender!

AD